Preview

Introduction to Sheet Metal Forming Processes

Better Essays
Open Document
Open Document
7131 Words
Grammar
Grammar
Plagiarism
Plagiarism
Writing
Writing
Score
Score
Introduction to Sheet Metal Forming Processes
Introduction to sheet metal forming processes

INTRODUCTION TO SHEET METAL FORMING PROCESSES

The documents and related know-how herein provided by SIMTECH subject to contractual conditions are to remain confidential. This documentation and related know-how shall not be disclosed, copied or reproduced by any means, in whole or in part, without the prior written permission of SIMTECH.

© 1999 SIMTECH. All rights reserved Product names are mentioned for identification only and may be registered trademarks.

SIMTECH 37 rue des Acacias, 75017 Paris FRANCE Tel: (33) (1) 56 68 80 00 Fax: (33) (1) 56 68 80 06

Copyright © 2001 SimTech Simulation et Technologie All rights reserved

page1/47

Introduction to sheet metal forming processes

INTRODUCTION: EVOLUTION OF INDUSTRIAL STAMPING
Back in 1985, the development cycle of a stamped part looked more or less like this (a sequential series of operations stemming from a single style design):
STYLE DESIGN

Process Dev. Product Devpt. Product Design P P d t 42 months

Soft/Hard tool built

Soft/Hard tool tryout

Today, people look at it rather as a sort of funnel, where key decisions are taken on the basis of different factors and alternative choices.

style product-process tooling CAM design validation tryout proces
18 months

production

Copyright © 2001 SimTech Simulation et Technologie All rights reserved

page2/47

Introduction to sheet metal forming processes

OVERVIEW: THE STAMPING SYSTEM AND STAMPING DESIGN
Like all complex system, stamping can be decomposed in hardware and software. By hardware we mean factors that cannot be changed from one operation to another. Conversely, by software we mean factors that the operator can change in order to obtained the desired result : a part with a given quality. HARDWARE Press Tools SOFTWARE Press set-up Material Lubrication The highlighted areas represent the components of the stamping design.

Copyright © 2001 SimTech Simulation et

You May Also Find These Documents Helpful

  • Good Essays

    Before the idea of interchangeable parts was discovered, broken parts had to be brought a special artisan and be repaired to order. Interchangeable parts replaced most of the tedious…

    • 1057 Words
    • 5 Pages
    Good Essays
  • Satisfactory Essays

    Ruby Training Guide

    • 6311 Words
    • 26 Pages

    No part of this publication may be copied, distributed, stored in a retrieval system, translated into any human or computer language, or transmitted in any form or by any means, without the prior written consent of VeriFone, Inc. The content of this document is subject to change without notice. The information contained herein does not represent a commitment on the part of VeriFone, Inc. Publications may not be stocked at the address given above. Requests for publications should be made to your VeriFone, Inc. Representative. GemCom, Ruby SuperSystem, Pearl, HPV-20, Sapphire, VeriPass, and Transaction SuperSystems are trademarks of VeriFone, Inc. All other products mentioned in this manual are trademarks or registered trademarks of their respective owners.…

    • 6311 Words
    • 26 Pages
    Satisfactory Essays
  • Good Essays

    Metal Fabrication

    • 1131 Words
    • 4 Pages

    Cutting is done by sawing, shearing, or chiseling (all with manual and powered variants); torching with hand-held torches (such as oxy-fuel torches or plasma torches); and via numerical control (CNC) cutters (using a laser, mill bits, torch, or water jet).…

    • 1131 Words
    • 4 Pages
    Good Essays
  • Good Essays

    As any other company, the purpose of Baxter Manufacturing Company was to improve their system so they can operate at a more efficient level. “They want to continue to be the leaders in manufacturing of deep-drawn stampings” (Wainright). The big issue is that Baxter thinks they should purchase a new software package while Collins argues that BMC should continue with the process of building the manufacturing systems.…

    • 562 Words
    • 3 Pages
    Good Essays
  • Powerful Essays

    Lel the Tank Train

    • 1138 Words
    • 5 Pages

    The contents of this document and/or media are not to be construed as an official Department of the Army position unless so designated by other authorized documents. The use of trade names in this document and/or media does not constitute an official endorsement or approval of the use of such commercial hardware or software. Do not cite this document for the purpose of advertisement. Do not release to other than the intended recipient(s).…

    • 1138 Words
    • 5 Pages
    Powerful Essays
  • Satisfactory Essays

    Seminar

    • 309 Words
    • 2 Pages

    Because this seminar was so successful, I have been authorized to contract with TurboNet Express for a continuing series of seminars on any topics related to emerging new technologies and trends as they apply to the needs of our company and our employees. I will call you on Monday so that we can arrange for a meeting to finalize some contractual issues.…

    • 309 Words
    • 2 Pages
    Satisfactory Essays
  • Powerful Essays

    Ethics Critical Thinking

    • 5300 Words
    • 20 Pages

    are made, decisions can even be irreversible. In this contribution three ways of deciding by highlighting critical, and reflective decision-making or systematic thought process as the most effective method…

    • 5300 Words
    • 20 Pages
    Powerful Essays
  • Good Essays

    We always seek to draw comparisons, and we are often unaware as to how seemingly irrelevant factors such as the simple presentation of options, actually influence what we select.…

    • 5130 Words
    • 21 Pages
    Good Essays
  • Good Essays

    Choices are essential for human growth. It is necessary to make decisions based off of…

    • 911 Words
    • 4 Pages
    Good Essays
  • Good Essays

    Circuit Board Fabricators Inc. uses a job shop process flow structure. The job shop process flow structure is a production of small batches of a large number of different products.The job shop process is also a flexible operation that has several activities through which work can pass. In a job shop, it is not necessary for all activities to be performed on all products, and their sequence may be different for different products.CBF, Inc. bases its board fabrication process on the average job size or on its typical order.…

    • 655 Words
    • 3 Pages
    Good Essays
  • Powerful Essays

    Agent Installation Guide

    • 15121 Words
    • 61 Pages

    Agent Installation Guide 5.0 - Documentation Release 1 This document, as well as the software described in it, is confidential and contains proprietary information protected by non-disclosure agreements. No part of this document may be reproduced in any form or disclosed to any party not bound by a non-disclosure agreement without the express written consent of Absolute Software Corporation. Absolute Software Corporation reserves the right to revise this document and to periodically make changes in the content hereof without obligation of such revisions or changes unless required to do so by prior agreement. Information contained herein is believed to be correct, but is provided solely for guidance in product application and not as a warranty of any kind. Absolute Software Corporation assumes no responsibility for use of this information, nor for any infringements of patents or other rights of third parties resulting from the use of this information. Absolute Software Corporation, Suite 1600, Four Bentall Centre, 1055 Dunsmuir Street PO Box 49211 Vancouver, British Columbia, Canada V7X 1K8. ©2010 Absolute Software Corporation. All rights reserved. Computrace®, Computrace Mobile™ and Absolute are registered trademarks of Absolute Software Corporation. All other trademarks are property of their respective owners. Computrace US Patents #5,715,174, #5,764,892, #5,802,280, #5,896,497 #6,244,758, #6,269,392, #6,300,863, and #6,507 , ,914. Canadian Patents #2,205,370 and #2,284,806. U.K Patents #EP793823, and #GB2338101. German Patent #695 125 34.6-08. Australian patent #699045. Japanese Patent #JP4067035. The Trademarks BlackBerry®, RIM®, Electron™, Pearl™, Pearl Flip™, Storm™, Curve™ and Bold™ are owned by Research In Motion Limited and are registered in the United States and may be pending or registered in other countries. Absolute Software Inc. is not endorsed, sponsored, affiliated with or otherwise…

    • 15121 Words
    • 61 Pages
    Powerful Essays
  • Powerful Essays

    Kevlar

    • 3498 Words
    • 14 Pages

    From this point onwards, the material you read will be the product of extensive research…

    • 3498 Words
    • 14 Pages
    Powerful Essays
  • Good Essays

    Mgt/230 Week 1 Assignment

    • 826 Words
    • 4 Pages

    People should make decisions every day, some of those decisions are easy to make, while others are quite difficult to implement. An appropriately combined and organized decision-making process will help to control this issue and bring a positive outcome for those involved. The decision-making process may become challenging for people due to “the lack of structure and entail risk, uncertainly and conflict” (Bateman and Snell, 2012, p. 86). That is why people trying to make important personal or professional decisions should have an appropriate model to follow in order to avoid these challenges. Bateman and Snell identified six steps or stages of decision-making process which may be attached to any problem or decision. First, it is necessary to identify and analyze the problem.…

    • 826 Words
    • 4 Pages
    Good Essays
  • Satisfactory Essays

    Zxwr Bbub

    • 1260 Words
    • 6 Pages

    ZTE CORPORATION or its licensors may have current or pending intellectual property rights or applications covering the subject…

    • 1260 Words
    • 6 Pages
    Satisfactory Essays
  • Good Essays

    Second Edition (May 2012) © Copyright Lenovo 2012. LIMITED AND RESTRICTED RIGHTS NOTICE: If data or software is delivered pursuant a General Services Administration “GSA” contract, use, reproduction, or disclosure is subject to restrictions set forth in Contract No. GS-35F-05925.…

    • 53835 Words
    • 216 Pages
    Good Essays