Preview

Radio Frequency Relay Control

Good Essays
Open Document
Open Document
1544 Words
Grammar
Grammar
Plagiarism
Plagiarism
Writing
Writing
Score
Score
Radio Frequency Relay Control
ABSTRACT: The RF relay control, as the name suggests, operates at Radio Frequency. The corresponding frequency range varies between 30 kHz & 300 GHz. In this RF system, the digital data is represented as variations in the amplitude of carrier wave. This kind of modulation is known as Amplitude Shift Keying (ASK). Transmission through RF is better than IR (infrared) because of many reasons. Firstly, signals through RF can travel through larger distances making it suitable for long range applications. Also, while IR mostly operates in line-of-sight mode, RF signals can travel even when there is an obstruction between transmitter & receiver. Next, RF transmission is more strong and reliable than IR transmission. RF communication uses a specific frequency unlike IR signals which are affected by other IR emitting sources. This RF module comprises of an RF Transmitter and an RF Receiver. The transmitter/receiver (Tx/Rx) pair operates at a frequency of 434 MHz. An RF transmitter receives serial data and transmits it wirelessly through RF through its antenna connected at pin4. The transmission occurs at the rate of 1Kbps - 10Kbps.The transmitted data is received by an RF receiver operating at the same frequency as that of the transmitter. The RF module is often used along with a pair of encoder/decoder. The encoder is used for encoding parallel data for transmission feed while reception is decoded by a decoder. HT12E-HT12D, HT640-HT648, etc. are some commonly used encoder/decoder pair ICs.

BLOCK DIAGRAM

TRANSMITTED SIDE: RECIEVER SIDE:
CIRCUIT DIAGRAM:

COMPONENTS USED:

• Encoder IC-HT12E

• Decoder IC-HT12D

• RF data transmitter module

• RF data receiver module

• Buffer IC-74541

• Relay driver IC-ULN2803

ENCODER: HT12E is an encoder integrated circuit of 212 series of encoders. They are paired



References: : http://www.circuitstoday.com/remote-control-circuit-through-rf-without-microcontroller#ixzz1YVVT7Q34 : http://jaspreetscodezone.blogspot.com/2008/01/interfacing-relays-using-parallel-port.html#ixzz1YQCdbpTh http://www.circuitstoday.com/remote-control-circuit-through-rf-without-microcontroller#ixzz1YVVhj6ju

You May Also Find These Documents Helpful

  • Good Essays

    Nt1310 Unit 9 Exam Paper

    • 486 Words
    • 2 Pages

    Signal spectrum – a transmission contains lack of high frequency components which means less bandwidth is required and direct current component is also desirable. With no dc component, ‘ac’ coupling via transformer is possible. Finally, the magnitude of the effects of signal distortion and interference depend on the spectral properties of the transmitted signal.…

    • 486 Words
    • 2 Pages
    Good Essays
  • Satisfactory Essays

    Unit 1 NT1310 Lab 1

    • 712 Words
    • 3 Pages

    When joined together these cells provide radio coverage over a wide geographic area. This enables a large number of portable transceivers to communicate with each other and with fixed transceivers and telephones anywhere in the network, via base stations, even if some of the transceivers are moving through more than one cell during transmission.…

    • 712 Words
    • 3 Pages
    Satisfactory Essays
  • Powerful Essays

    Frequency modulation (FM) - changes the carrier frequency according to the information being conveyed. In FM, unlike the PM, the…

    • 878 Words
    • 4 Pages
    Powerful Essays
  • Good Essays

    unit 8 assignement

    • 920 Words
    • 3 Pages

    Radio waves offer another benefit to the wireless system in addition to their range. With radio signals it is possible for multiple carriers to exist in the same space at the same time without interfering with each other. The key to making this possible is variation of frequencies. As long as concurrent frequencies are no…

    • 920 Words
    • 3 Pages
    Good Essays
  • Good Essays

    It 242 Week 8 Assignment

    • 686 Words
    • 3 Pages

    Microwave signals transmit using electromagnetic energy. Microwave signals are used commonly in long distance telephone telecommunications, cellular phone networks, and television networks. Microwaves travel in a straight line the wave can be narrow beamed making it more effective for long distance transmissions.…

    • 686 Words
    • 3 Pages
    Good Essays
  • Satisfactory Essays

    ect114

    • 1514 Words
    • 7 Pages

    An encoder is used in most wireless devices such as garage door openers to help filter out interference from other devices.…

    • 1514 Words
    • 7 Pages
    Satisfactory Essays
  • Powerful Essays

    -RFID TAGS- USES RADIO FREQUENCY ELECTROMAGNETIC FIELDS TO TRANSFER DATA FOR PURPOSES OF AUTOMATIC IDENTIFICATION AND TRACKING.…

    • 1964 Words
    • 8 Pages
    Powerful Essays
  • Powerful Essays

    Energy, in the form of electromagnetic radiation, exerts steadily oscillating force on charges (electrons). The force is originally exerted strongly in one direction, but then reverses for the cycle to continue. The radio waves push on the electrons in the metal in the antenna, causing the oscillating up and down the length of the source (antenna). The current is this created in the antenna.…

    • 1890 Words
    • 7 Pages
    Powerful Essays
  • Better Essays

    We know that electromagnetic radiation is produced by accelerating charges. In the radio transmitter, electrons oscillate up and down and are thus accelerating. An electron will exert a force on another electron when they are some distance away, like charges repel. When the electron in the transmitter oscillates up and down, the direction of the force it exerts changes since the source of the force is moving. It takes some time for the change in this direction of the force to be felt since this change is communicated or propagated out at the speed of light. In addition, the horizontal component of this force is canceled by the positive charges in the transmitting antenna. So, the resulting force is an oscillating force that pushes vertically on electrons. This force propagates out as a wave as the signal travels at the speed of light.…

    • 1154 Words
    • 5 Pages
    Better Essays
  • Good Essays

    The technology in which the parameters such as amplitude, phase and frequency of radio frequency waves are changed so as to transmit and receive the information is known as RF technology or radio frequency technology. In this, the electromagnetic waves that lie in the range of 3 khz to 300 Ghz are used for the wireless communication between the two devices. The signal is modulated at the transmitter end and then the antenna converts this electrical signal into the radio waves and emits them. The medium in which they travel is space. The receiving antenna catches the waves at the receiving end and then the signal is demodulated and converted back to its original form. These waves are highly affected by the interference…

    • 648 Words
    • 3 Pages
    Good Essays
  • Good Essays

    Wireless Proposal

    • 738 Words
    • 3 Pages

    As the businesses are emerging, they require advanced technologies. Wireless technologies are facilitating the businesses in many different ways. Wireless devices and wireless transmission media are technologies used in today’s business. Latest wireless devices such as android phones, I-phones, I-pads, laptops, PDA’s and wireless navigation systems provides businesses with various flexibilities.…

    • 738 Words
    • 3 Pages
    Good Essays
  • Good Essays

    Rfid Based Attendance System

    • 17989 Words
    • 72 Pages

    LIST OF FIGURES 2.1 General Block Diagram. 18_ 2.2 Block Diagram Showing Inside View of Controller Section. 20_ 2.3 RFID Module. 23 _ 3.1 Entire Circuit Diagram.…

    • 17989 Words
    • 72 Pages
    Good Essays
  • Good Essays

    The project Ultrasonic Distance Meter is a very interesting and useful project for many industrial applications. In this project we have used the ultrasonic waves to measure the distance in between two points. The basic principal is based on the speed of ultrasonic waves in open air. We have used a microcontroller AT89S51 to transmit and receive ultrasonic waves through 40 KHz ultrasonic receiver and transmitters. By measuring the time required to travel the unknown distance by ultrasonic waves in air we can find out the distance between two points. The distance measured is displayed on a LCD display. The transmission & reception of ultrasonic waves is very complex in nature so it needs very sophisticated techniques to process these waves. We have used a very complex structure of amplifier and filters for this purpose. The speed of ultrasonic waves is dependent on temperature. So before using ultrasonic waves for any measurement we need to calibrate the speed of ultrasonic waves in current atmospheric temperature. For this purpose we have implemented a special algorithm to calibrate the speed of ultrasonic waves through a known distance of 100 Cm.…

    • 1997 Words
    • 8 Pages
    Good Essays
  • Good Essays

    The ATA has a series of smaller dishes that bring radio waves to a focus point just like a large dish and converts them to electric signals…

    • 996 Words
    • 4 Pages
    Good Essays
  • Powerful Essays

    is the opposite of information. Something that is redundant adds little, if any, information to a message. Redundancy is important because it helps combat noise in a communication system, e.g. in repeating the message.…

    • 2378 Words
    • 10 Pages
    Powerful Essays