Raymond mill several troubleshooting methods
Raymond mill in the course of this malfunction , according to the following processing :
Raymond mill is a common fault : no less powder or flour production is low .
Causes: ( 1 ) Locks powder is not adjusted, Mifengbuyan , resulting powder suck . ( 2 ) blade wear and material shovel can not afford .
Remedy: ( 1 ) checking and adjusting locks sealed powder was found to be leaking at the blade . ( 2 ) Replace the blade .
Raymond Mill Troubleshooting II : refined powder too thick or too thin .
Causes: ( 1 ) analysis of turbine blades wear serious , can not afford grading effect. ( 2 ) fan flow inappropriate .
Remedy: ( 1 ) Replacement blade length appropriate off a small amount of solution into the wind turbine is too rough . ( 2 ) too small and should be increased inlet air volume .
Raymond Mill Troubleshooting III : Host current rise , local temperature rises , the fan current drops .
Reason: ( a ) feeding excess powder duct is blocked, poor exhaust pipes , circulating air heat so that the main current , machine temperature rises , the fan current drops .
Remedy: ( 1 ) reduce the feed rate to clear the air duct of accumulated powder . ( 2 ) open big I duct valves, temperature control of the material into the machine at 6 ℃ or less.
Raymond Mill Troubleshooting four : Raymond Host noise and have greater vibrations.
Reason: ( a ) feeding quantity small . Badly worn blade , shovel can not afford materials , anchor bolts loose. ( 2 ) the impact of large hard material , or non- material material layer ( 3 ) Roller grinding ring out of round deformed .
Remedy: ( 1 ) Adjust the feeding amount , replacement blade . ( 2 ) replacement of feed size . ( 3 ) replace the roller , grinding ring .
Raymond Mill five common faults : fan vibration .
Reason: ( a ) powder or worn blades on a plot of imbalance . ( 2 ) anchor bolts loose.
Remedy: ( 1 ) removal or replacement blades blade accumulated powder . ( 2 ) tighten the anchor bolts .
Raymond Mill
Raymond mill is a common fault : no less powder or flour production is low .
Causes: ( 1 ) Locks powder is not adjusted, Mifengbuyan , resulting powder suck . ( 2 ) blade wear and material shovel can not afford .
Remedy: ( 1 ) checking and adjusting locks sealed powder was found to be leaking at the blade . ( 2 ) Replace the blade .
Raymond Mill Troubleshooting II : refined powder too thick or too thin .
Causes: ( 1 ) analysis of turbine blades wear serious , can not afford grading effect. ( 2 ) fan flow inappropriate .
Remedy: ( 1 ) Replacement blade length appropriate off a small amount of solution into the wind turbine is too rough . ( 2 ) too small and should be increased inlet air volume .
Raymond Mill Troubleshooting III : Host current rise , local temperature rises , the fan current drops .
Reason: ( a ) feeding excess powder duct is blocked, poor exhaust pipes , circulating air heat so that the main current , machine temperature rises , the fan current drops .
Remedy: ( 1 ) reduce the feed rate to clear the air duct of accumulated powder . ( 2 ) open big I duct valves, temperature control of the material into the machine at 6 ℃ or less.
Raymond Mill Troubleshooting four : Raymond Host noise and have greater vibrations.
Reason: ( a ) feeding quantity small . Badly worn blade , shovel can not afford materials , anchor bolts loose. ( 2 ) the impact of large hard material , or non- material material layer ( 3 ) Roller grinding ring out of round deformed .
Remedy: ( 1 ) Adjust the feeding amount , replacement blade . ( 2 ) replacement of feed size . ( 3 ) replace the roller , grinding ring .
Raymond Mill five common faults : fan vibration .
Reason: ( a ) powder or worn blades on a plot of imbalance . ( 2 ) anchor bolts loose.
Remedy: ( 1 ) removal or replacement blades blade accumulated powder . ( 2 ) tighten the anchor bolts .
Raymond Mill