DETERMINATE CANTILEVER TRUSS 1.0 OBJECTIVE 1.1 To observe the effect of redundant member in a structure in a structure and understand the method of analysis type of this structure. 2.1 LEARNING OUTCOME 2.2 The application of the engineering knowledge in practical application 2.3 To enhance technical competency in structural engineering through laboratory application 3.0 THEORY 3.1 In a statically indeterminate truss‚ static equilibriumalone cannot be used to calculated member force. If we were to
Premium Beam Continuum mechanics Experiment
Truss bridges were invented in the year of 1844. The first Truss to be invented was the Pratt Truss. This is because Caleb and Thomas Pratt invented the bridge. The basic types of Trusses are Warren‚ Pratt‚ Howe and K Truss. These are just the four that people use most commonly. The Truss Bridge is almost like a beam bridge with braces. The Truss Bridge can either be a through Truss or a Deck Truss. A Through Truss means that the deck of the bridge is under the bars or braces of the bridge. A Deck
Premium Bridge Truss Bridges
HSC ENGINEERING STUDIES CONSTRUCTION TASK TRUSS BRIDGE [pic] BY RICHY R. THURUTHIYIL CONTENTS Common types of Trusses 1- Warren Truss [pic] A warren truss consists of alternatively inverted equilateral triangles which are rigid. It is made up of horizontal members and equal
Premium Truss Bridge Compressive stress
Objective The objective of the project is to build a truss that would be able to take a specific amount of downward force remarkably with respect to the weight of the truss itself‚ i.e. to construct a truss that would hold a relatively high efficiency score. And construct the bridge in such a way to as to keep the deflection of the structure at minimal. Introduction First of all‚ what is a truss? In an engineering view‚ a truss is a structure that is made up of series of triangular unit made
Premium Bridge Truss Beam
1. Cohen calculated Nike’s weighted average cost of capital (WACC) to be 8.3%. I find error in this calculation as a result of the following points of disagreement: a) Weighting of Capital Structure: Use of book values of capital rather than the market values b) Cost of Debt Calculation: Incorrect method for calculating debt c) Tax Rate: Use of a tax rate derived from the summation of state and statutory taxes instead of the firm’s marginal tax rate 2. Revised Calculation of WACC: WACC
Premium Interest
Monette G. Calamba CSIII June 22‚ 2011 1. History and generation of computer. 2. Definition of Mechanical Calculating Device. * First Generation (1941-1956) World War gave rise to numerous developments and started off the computer age. Electronic Numerical Integrator and Computer (ENIAC) was produced by a partnershp between University of Pennsylvania and the US government. It consisted of 18‚000 vacuum tubes and 7000 resistors. It was developed by John Presper Eckert and John W
Premium Computer ENIAC Integrated circuit
Truss bridges are recognizable because of their numerous‚ relatively small interconnected triangles. This framework of triangles is used for is strength to withstand tension and compression forces. They are considered a light-weight yet a very stiff form of construction. At first they were built of wood‚ then with the discovery of welding they began to build then using iron‚ then steel. Occasionally‚ a combination of the materials may be used. There are actually 30 different kinds of truss bridges
Premium Management Project management Construction
Truss Bridge Physics 141 Robin Hoffmeister There is many reason that we need bridges in every day of our life‚ from sufficient means to pass over a roadway‚ waterway‚ railway‚ or other structure. You don’t even think about them because it takes no effort to get over them and they are just there for your use. So if you don’t think of them for everyday use I highly doubt that you would think of the physics that is involved in putting one together or the kind of force the bridge can actually
Premium Truss Bridge Force
Introduction What is a Truss? A truss is a structure made up of triangular components forming a very ridged structure. A truss can take the force form one location and distribute it over the whole structure. Trusses have been around since the start of modern history and where originally made from stone and over time people discovered that iron and wood have great strength when used under tension and compression. The Importance of Trusses Before the industrial revolution almost all trusses in use
Premium Truss Bridge
is a truss‚ which is a structure of associated components that shape triangular units. In the late nineteenth century and early twentieth century‚ more than half of the bridges that were made‚ were made out of stone. But since the United States had so much wood‚ they made a lot of wooden bridges in those times and a vast majority of them were truss bridges. As the years passed on‚ the real iron and steel organizations are gone‚ truss bridges stay as their legacy. One of the most famous truss bridges
Premium China Bridge Industrial Revolution