strain. Problem 4: A student reads that the Young’s modulus of elasticity for cast iron is 2.1x1011 Pa and that the cast iron fails abruptly when a strain of 0.0005 is reached. From this information‚ what would be the stress needed to break the specimen of this material in a tensile test? What assumption is being made here. Problem 5: The UTS of a grade of aluminium is 1x108 Pa. What is the maximum tension that is possible in a wire of this material with a cross sectional area of 2.5 x 10-7 m2. What assumption
Premium Tensile strength Elasticity
Case study outline for Unit CU3049 Section 1: setting the context Describe the two learners you are going to be using for the case study and the programme which you are assessing. These can be learners you have actually worked with‚ or learners who you imagine you would work with‚ or a composite of learners you have known. If they are different from each other‚ this allows you to provide more evidence as you explain how you will adapt to each. Explain the assessment strategy that applies
Premium Management Assessment Planning
Chapter 7 David Connor 1. The ____________ motor is the most common motor used in hermetically sealed units. a. Capacitor-start‚ induction run b. Repulsion-start‚ induction run c. Induction run d. Induction run two phase and polyphase 2. Of the four listed motors‚ which is the most commonly used on external drive‚ belt driven compressors? e. Induction two-phase and polyphase.
Premium Electric motor Inductor Voltage
SPSS HW#7 Question #1 Model Summaryb | Model | R | R Square | Adjusted R Square | Std. Error of the Estimate | Dimension0 | 1 | .351a | .123 | -.169 | 3.9429207 | a. Predictors: (Constant)‚ x | b. Dependent Variable: y | ANOVAb | Model | Sum of Squares | df | Mean Square | F | Sig. | 1 | Regression | 6.560 | 1 | 6.560 | .422 | .562a | | Residual | 46.640 | 3 | 15.547 | | | | Total | 53.200 | 4 | | | | a. Predictors: (Constant)‚ x | b. Dependent Variable: y | Coefficientsa
Premium Regression analysis
Consolidated Products Case Analysis Abstract This brief paper’s objective is to analyze the managerial behavior of two managers‚ Ben Samuels and Phil Jones‚ who worked for Consolidated Products plant. The analysis will concentrate on how these individuals displayed their specific relation-driven behaviors‚ and specific task-oriented behavior‚ and the subsequent managerial grid model. In addition‚ this paper will describe and compare to what extent each manager used participative or inspirational
Premium Leadership Management
NCB OFFICE PRODUCTS INC. Executive Summery NCB is a manufacturer and distributer of a wide range of office products. In Canada‚ NCB uses several distributers in different regions. One of the major distributers is Harrison Stationary and Office Supply LTD. Harrison had distributed NCB’S products for over 50 years and NCB was the largest supplier of Harrison. In January 2003 Harrison was acquired by the president of the company and four senior officers. Most of the acquisition cost was financed
Premium Balance sheet Accounts receivable Accounting software
CLASSIFICATIONS OF PRODUCT INTRODUCTION: The influx of wide ranges of consumable into the Nigerian market has provided a corresponding wide range of choice to the consumers. The competitive nature of the market place has therefore become a significant factor that producers can only ignore to their own peril. The purchasing power of the consumers is also affected by the economy of the Nation. It is as a result of the se factors that manufacturers must of necessity
Premium Marketing Goods Service
PRODUCT MIX A product mix is the set of all products and items that a particular seller offers for sale to buyers. Product mix has a certain width‚ length‚ depth‚ and consistency. Width: No. of different product lines e.g. P& G carries width of five lines- Detergents‚ Bath soaps‚ Toothpaste‚ Disposable Diapers‚ Paper Tissues. Length: Total no. of items in its product mix. Depth: No. of variants of each product in the line. Consistency: refers to how closely related the various product
Premium Marketing Consumer theory Business
Number 3. 3. What is the result? Diskpart Successfully extended the partition 4. What is the result? I can access the Server DC but I still do not see any install folder. 5. How much available shrink space is contained in the volume? 449MB 6. How is the last volume you created different from the previous ones? Explain why. The size of the volume is different. By shrinking the file it made the volumes less than 2000MB 7. What do you suppose would happen if you created another simple volume out
Premium Volume Operating system File system
Jessica Ho 11-6-12 ACG 6425 Case 22-4 – Enager Industries‚ Inc. 1. McNeil’s project was rejected because it only provides a 13% return and does not meet the minimum return of 15% mandated by Henry Hubbard. Although the project does create some increase in earning per share‚ it does not provide the required return to keep up with the interest rates the corporation had been paying on the recent borrowings. 2. Randall and Hubbard seem to have disregarded that each of the divisions
Premium Investment Interest Project management