Alum Lab Conclusion The purpose of this laboratory was to use two different techniques to attempt to identify the melting point and the mole ratio of hydrated water to anhydrous aluminum‚ potassium‚ and sulfate of AlKSO4. The hypotheses were: if the alum was put in a capillary tube the melting point of alum will be able to be determined; and the water of hydration in alum crystals will be possible to determine if the alum is heated with a Bunsen burner. Results: Part 1: Data Table | Trial
Premium Chemistry
Analysis of Alum‚ AlK(SO4)2・12 H2O Partner: Cindy Date: Sep 15‚ 2011 Purpose: The purpose of this experiment is to verify the identity of the alum by finding the properties of the substance; melting point and mole ratio of the water to the anhydrous. Every substance has unique characteristics which help to determine the identity of it. The actual values of the properties can be compared to the experimental values. In real life‚ this can be used to determine the unknown medicines. Hypothesis:
Premium Mole Laboratory equipment Temperature
AP Chemistry Lab 2: Analysis of Alum Lab Objective: In this lab we will analyze alum by two techniques in order to verify its identity. The melting point and the mole ratio of hydrated water to anhydrous aluminum potassium sulfate will be determined. Lab Procedure: 1. Use a mortar and pestle to crush alum. 2. Pack the alum in capillary tube‚ and then fasten it to the thermometer. 3. Fasten the thermometer to the ring stand. 4. Immerse the bottom of the
Premium Chemistry Water Oxygen
synthesize alum‚ test for various ions in alum‚ and form crystals in aqueous alum solution. The alum was synthesized from aluminum foil and run through a filtration system to isolate the alum. 2 Al(s) + 2 KOH + 22 H2O + 4 H2SO4 → 2 KAl(SO4)2●12H2O(s) + 3 H2(g) Its composition was analyzed using two precipitation tests and two flame tests. Three methods for growing crystals were then set up for observation next lab. Theoretical yield and percent yield: The theoretical yield for alum was 4.55g and
Premium Chemistry Water Sodium
The purpose of the making alum from aluminum lab was to create alum from a series of chemical reactions involving aluminum. Small pieces of an aluminum can were cut and measured before being taken through a series of chemical reactions. This process involved filtering out waste product that was no longer needed in the reaction by using Whatman #4 filter paper and an aspirator. The first reaction that took place was placing aluminum pieces into the strong base NaOH and then heating it. This reaction
Premium Chemistry Chemical reaction Water
1) Heading a. Analysis of Alum b. September 8‚2010 – September 10‚2010 c. Asad Mehmood d. Lab Partner: Alec Drey‚ Sarah Schrader‚ Seth Kerrey 2) Purpose e. Research Problem: Is what we have alum? In this lab‚ we will be analyzing alum by doing three different tests. The first will be to find the melting point‚ the second to find the amount of water in alum‚ and the third is to find the percent sulfate. We expect the values to be close to the actual.
Premium Chemistry Scientific method Experiment
Conclusion 1: In this first lab we attempted to discover which of the materials given to us were hydrates by heating them and then dissolving them in water. Our results showed that all of our substances were hydrates besides the sucrose‚ sucrose if the only one which did not both bring condensation when heated and dissolve in water‚ which agreed with our hypothesis because we also thought that sucrose was going to be the only one that wasn’t a hydrate. The only error that we may have encountered
Premium Heat Water Chemistry
Lab Conclusion When comparing the average speed results from part two of the lab and the definition of acceleration‚ you find similarities between the two. First‚ average speed is distance divided by time‚ and we use it to describe the motion of an object moving at changing speeds. We can see this from our lab results from the average speed of the marble traveling down the ramp‚ because it picks up speed. When the marble is released at the top of the ramp‚ the ball doesn’t have the same momentum
Premium Velocity Kinematics Analytic geometry
Conclusion In this experiment‚ we measured the mass of 4 gasses; oxygen‚ carbon dioxide‚ helium‚ and lab gas. We took a Ziplock bag‚ and turned into a non-stretchy balloon‚ and filled with each gas and measured the apparent mass then calculated the actual mass‚ then find a ratio between the mass of oxygen and the other gasses. We tried to keep the pressure about the same each time so our calculations would be more accurate. We found out that the heaviest was carbon dioxide‚ and the lightest
Premium Oxygen Carbon dioxide
Conclusion to Motion Lab Kerreon Wright 3rd Period Ms. Gislason The purpose of this Motion Lab was to find the acceleration of a steel marble going down a straight track six different times to figure out how an object’s mass affects acceleration. It doesn’t due to Newton’s second law of motion. There were six different accelerations for each trial and they are: 7.88 m/s squared‚ 6.78 m/s squared‚ 6.07 m/s squared‚ 5.57 m/s squared‚ 4.32 m/s squared‚ and 5.11 m/s squared. It’s possible
Premium Classical mechanics Newton's laws of motion Mass