DENSITY OF LIQUIDS AND SOLIDS by Lab instructor: Due date: Results and discussion: The purpose of the experiment was to determine the densities of the unknown liquid and solid as precisely and accurately as possible in order to identify them. It was carried out first on distilled water in order to rule out systematic errors. A 10 mL beaker was placed on a top pan balance and “tared”. The beaker was then removed and 10 mL of distilled water was pipetted into it before it was placed
Premium Water Chemistry Volume
DENISTY LAB 2/25/13 Chemistry H. Mrs. Halme Objective: Your task is to determine the density of 3 known metals: Zinc‚ Copper‚ and Lead. They are each marked. You must then calculate the density of an unknown metal and determine its identity based on your data from your known samples. Reagents: None Equipment: Lead Copper Zinc Triple Beam Balance Graduated cylinder Unknown metal (Magnesium) Beaker Calculator Procedures Preparation: We observed the given equipment
Free Calculator Mathematics Division
Matt R Results & Analysis Part 1: 1.) To determine the density and composition of a penny it must be first weighed on a scale. Find the average mass of multiple pennies from the same year. After weighing it find the volume by placing the pennies into a 50 ml beaker with 15 ml of water. Note the change in volume to obtain the volume of the pennies‚ obtain the average volume‚ and then calculate the density by dividing the mass of the penny by the volume. 2.) To keep measurements accurate and precise
Premium Density Mathematics Volume
Measurement of the Densities of Water and Alcohol Phuc Truong and Shane Steele Data Collected: September 8‚ 2014 2:05 P.M. Purpose: The purpose of the experiment is to measure the densities of liquids. Specifically‚ the two liquids that were used and measured in the research were deionized water (H2O) and alcohol (C2H5OH). Methods: Density is an intensive quantity that cannot be visually identified. Therefore‚ the most straightforward approach to this problem was to record the measurements of mass
Premium Water Volume Density
1. DATA: Table 1: Density based on dimensional analysis Trial 1 Trial 2 Trial 3 Units Mass of sample 70.5466 70.5467 70.5465 g Dimensions of sample Length 4.98 4.98 4.99 cm Width 1.21 1.22 1.21 cm Height 1.21 1.22 1.22 cm Volum of sample 7.29 7.41 7.37 cm^3 Density of sample (based on dimensional analysis) 9.68 9.52 9.57 g/cm^3 Table 2: Density based on the displacement of water Trial 1 Trial 2 Trial 3 Units Mass of sample 70.5467 70.5465 70.5466 g Final
Premium Density Volume Water
22ºc Part B Aluminum Sinker 1. Mass of object. 6.87g 49.44g 2. Volume of the water in the graduated Cylinder after the addition of the object. 17.5mL 19mL 3. Volume of the object due to displacement 2.5mL 4mL 4. Density of object. 2.748 12.36 5. Calculated mass of the sinker in ounces 1.74g Part C 1. Length of the foil 8.5cm 2. Width of the foil 8.5cm 3. Mass of the foil .60g 4. Volume of the foil .222 5. Thickness of the
Premium Density Kilogram Measurement
Measuring the Density of Ball Bearings/ Density Aaysha Dawood Chem 1211L-198 September 7‚ 2012 Procedure: The procedure for this lab was taken from the lab manual below: Block/McKelvy (2012). Laboratory Experiments for Chem 1211L & 1212L Cengage Learning (7th ed.)‚ p. 5-19 (Measuring the Density of Ball Bearings/Density). No changes occurred that were different from the procedure listed above. Data: Measuring the Density if Ball Bearings | Ball 1 | Ball 2 | Ball 3 | Ball 4 |
Premium Force Classical mechanics Mass
Experiment Density‚ Accuracy‚ Precision And Graphing OBJECTIVES 1. The determination of the density of water 2. A comparison of the accuracy and precision of a graduated cylinder and a pipet EXPERIMENTAL MATERIALS Part A A 50mL graduated cylinder A balance 50.0mL deionized water A rubber policeman Part B A 100mL beaker A 50mL graduated cylinder A volumetric pipet 120.0mL deionized water A thermometer A rubber policeman
Premium Density Volume Measurement
Abstract The purpose of this experiment was to identify whether density is an extensive or intensive physical property. By using water displacement‚ the volumes of the paper clip samples were measured and the masses were obtained by using an electronic balance. Each mass and volume was unique to their sample so by using their values‚ density was used to identify substances in the lab. After conducting the experiment‚ the results showed that there was a positive slope between the different paper
Premium Temperature Physical quantities Density
hi 1. Which of these is not correct as a basic property of electric charges? (a) Total charges in an insulated system is invariable (b) A charged body is electrically unstable (c) * A charged body has equal number of positive and negative charges (d) Positively charged body is deficient of electrons x+q1+q2 = 2 q1 2.Calculate the distance x between charges q1 and q2 shown‚ given the repulsive force between them as 1.2 x 10-4 N‚ take the permittivity of vacuum
Premium Magnetic field Electromagnetism Electric charge