! Name: Laura Romero ! 5.04H: Gas Stoichiometry Lab Worksheet Data and Observations: Present all relevant data in a data table below. Include an observations section for any observations that you made during the lab. (5 points) Data Table Mass of magnesium strip (grams) 0.032 g Volume of gas collected (mL) 30mL Barometric pressure (atm) 1.1 atm Room Temperature (°C) 22 °C Vapor pressure of the water (torr) 19.8 torr ! ! Calculations: ! 1. Write the
Premium Pressure Stoichiometry
Preparation and Recrystallisation of Aspirin Contents Page Synopsis iii 1 Introduction 1 1.1 Objective 1 1.2 Background 1 2 Theory 1 3 Procedure 2 3.1 Materials 2 3.2 Preparation 2 3.3 Recrystallisation 3 3.4 Determination of Melting Point 3 4 Results and Calculation 4 4.1 Mass 4 4.2 Percent yield 4 4.3 Melting Point 4 4.4 Appearance 4 5 Discussion 5
Premium Acetic anhydride Acetic acid Aspirin
JOMO KENYATTA UNIVERSITY OF AGRICULTURE AND TECHNOLOGY DEPT: CIVIL ENGINEERING UNIT: CHEMISTRY 1 (SCH 2109) PRACTICAL REPORT EXPT 2: Standardization and Determination of Concentration of Hydrochloric Acid in a Given Solution by ARAKA BRAMWEL MBOGO EN251-0221/2010 TITLE: STANDARDIZATION and DETERMINATION OF THE CONCENTRATION OF HYDROCHLORIC ACID PRESENT IN A GIVEN SOLUTION Aims: To be able to standardize Sodium Hydroxide (NaOH) solution using a standard solution of Oxalic acid
Premium Titration Sodium hydroxide Chlorine
OF EXPERIMENT The purpose of this lab was to determine the magnitude of the uncertainties produced when making measurements using common lab equipment. II.APPARATUS AND MATERIALS NEEDED safety goggles distilled water (at 20°C) laboratory apron dropper laboratory balance 2 objects of unknown mass standard masses graduated cylinder‚ 10-mL graduated cylinder‚ 100-mL III.PROCEDURE Part A: Estimating the Uncertainty of a Balance 1.We put on lab aprons and goggles. Then‚ we used the
Premium Mass Measurement Uncertainty
absorbance at 470 nm since it is known to keep an acidic solution throughout the entirety of the experiment. It was important to do this right at the beginning of the lab since the zeroed value of the acid was the calibration number for all of the other solutions. A total of seven solutions with different dilutions were used throughout the lab to conduct the equilibrium constant. The first step was adding 5 mL of 0.200 M Fe(NO3)3to each of the 5 test tubes. Once this was done‚ 0.00200 M NCS was added to
Premium Metrology Laboratory glassware Volume
Lab Report Experiment 1 & 2 CHM-101 Amele Takpara Partner: Jessamyn Dupree ------------------------------------------------- Experiment 1 ------------------------------------------------- (Pre-Lab Questions) 1. In the design of a Bunsen burner‚ explain the purpose of a. the gas control valve The gas control valve regulates the rate at which methane enters the burner. b. and the air vents. The air vents control the rate at which air enters the burner 2. Why is a luminous
Premium Temperature Volume Liquid
Title: Calculating the Atomic Mass of “Pennium” Purpose: The purpose of this lab is to calculate the atomic mass of “pennium” using pennies made before 1982 and pennies made 1982 or after. Hypothesis: The atomic mass of the pennium will be the average of the average masses of a pre-1982 penny and a post 1982 penny. Procedure: 1. Obtain a bag of pennies 2. Determine the total number of pennies in the bag. Record the value. 3. Sort the pennies by date into 2 piles. One pile should consist
Premium Atom Isotope Copper
Willy Rupprecht Date(s) performed: October 2 - 3‚ 2012 Gravimetric Analysis of an Unknown Group 1 Metal Carbonate Purpose: The purpose of this lab is to determine the identity of a Group 1 metal carbonate compound by gravimetric analysis. Procedure: The unknown carbonate is weighed and then dissolved in water. A solution of CaCl2 (calcium chloride) is added to the metal carbonate solution to precipitate the carbonate ions as CaCO3 (calcium carbonate). The precipitate is then filtered‚ dried
Premium Calcium Filter paper Gravimetric analysis
Check-List for Laboratory Reports 1. Your lab report must be written by word processor or by hand. Note that if it is written by hand it is your responsibility to ensure that it is legible and written in ink. 2. You must attach a cover sheet that will be the front of the report that contains your name‚ student ID‚ rotation number‚ and the name of your TA. Your rotation number = 1 if you are in my tuesday class and your rotation number = 2 if you are in my wednesday class. Failing to provide
Premium
Molar Mass Lab 3.09 Molar Mass of Compounds Purpose: The purpose of this experiment is to determine the formula of a copper sulfate hydrate by heating it up. Materials: Hydrate‚ crucible‚ balance‚ Bunsen burner and scale Procedure: First you measure the mass of the empty crucible and record that mass. Then you should fill the crucible with 3-5 scoops of the hydrate and record that mass as well. Heat the hydrate filled crucible above the Bunsen burner for 10 minutes for all f the water to evaporate
Premium Water Mass Addition