Natasha Tenen Lab: Thursday (3-6 pm) OSMOSIS LAB REPORT INTRODUCTION Osmosis is a special type of diffusion where water molecules move down a concentration gradient across a cell membrane. The solute (dissolved substance) concentration affects the rate of osmosis causing it either to speed the process up or slow it down. Based on this‚ how does different concentrations of sucrose affect the rate of osmosis? If sucrose concentration increases in the selectivity-permeable baggies‚ then the
Premium Water Concentration Solution
HAEF Psychico College ENVIRONMENTAL SYSTEMS & SOCIETIES LAB REPORT (SL) TITLE OF LAB : Investigation of the impact of overpopulation in biodiversity Objective of the investigation: To investigate the impact of climate change in biodiversity Research Question: How does the temperature change ( each pot will be held in 35°C‚ 20°C‚ 10°C‚ 0°C‚ -10°C respectively) influence the growth of lettuce plants calculated from the measurement of the weight of each plant every 2 days
Premium Plant Water Light
Lab report for Experiment #2: Extraction Your Name: Name of TA: Lab Partner’s Name: Lab Section: Title: Experiment #2: Extraction Purpose: What is the purpose of this lab? In your OWN words! Observations: Weighed out 3.2568 grams of chemical mixture that was yellow in color. Dissolved dry chemicals in 38 ml CH2Cl2 with gentle heating. Poured the yellow solution into sep funnel. Added 10 ml CH2Cl2 to flask to rinse‚ poured solution into sep funnel. Added 15 ml 3 M
Premium PH Solubility Chemistry
Page I - Cover sheet In the middle f the page give name and number of your microorganism In the right lower corner provide - your name - Lab section number (Biol 108-005) - Date submitted ( 4/18/2013) - the unknown tube # is 5 Page II table of result - This page will have your table of results include the following information - Name of the test - Medium used - Indicator used - your results Part III - All the test done As many pages as needed to do a complete job. in this section
Premium Organism Bacteria Biology
Experiment AM1.2—Centrifugal Force Student name JunJie Liu Student ID 1512042 Experiment Date 11 Feb 2015 Lab group Mech 7 Introduction In this lab report we show the basic methods of measuring centrifugal force using two counter balanced bell-cranks spin on a turntable (shows in figure 1) and able to calculate the centrifugal force with given conditions shows in figure 1. *Figure
Premium Force Torque Experiment
Physics Lab report Aammar Paracha Section MX Feb 6th 2015 OPTICS Abstract: This experiment revolves around using light rays and lenses. The experiment also discusses different properties of light rays. This experiment uses different lenses and measurements to produce images and observes different techniques to obtain the image position. Question and Answers: 1. Use your data to verify the Law of Reflection and then use Snell’s Law to calculate
Premium Optics Lens
’Neil 2002). The particular conditions that had to exist for this to apply were that the population had no mutation‚ had no natural selection‚ was a large population‚ had only random mating‚ and had no migration. For the cases to follow later in the lab‚ Cases 1 and 2 exemplify Hardy-Weinberg conditions. All of the others either have selection or not enough members in the population‚ which will be the most-closely observed
Premium Biology Experiment Evolution
Raquel Johnson October 19‚ 2014 Solids: Recrystallization and Melting Points Organic Chemistry 2423 Lab Report: Recrystallization Abstract: The purpose of this lab was to purify an unknown compound by recrystallization. Taking an unknown compound and identifying it by purifying it from its impurities through the use of hot gravity filtration. Then to determine the unknown you were to take the melting point. An unknown compound was recrystallized from hot water to produce 0.99 grams (67% recovery)
Premium Temperature Solubility Solid
Introduction and Purpose: This lab focuses on how weight affects the time it takes for a rotocopter to fall from a drop height of 1 and 2 meter(s) respectively. The primary goal of this lab is to investigate and explain the relationship of these two factors. During the process of conducting this experiment‚ learning to design a lab will also be achieved. Research Question: What is the effect of weight on the time it takes for a rotocopter to fall from a drop height of 1 and 2 meter(s)? Variable
Premium Force Classical mechanics Mass
Impurity Lab Report Aim: To find out the difference of the boiling point and melting point when adding impurity (salt) to water. Diagram: Method: 1.Set up the apparatus as shown in the diagram 2. Get a known amount of ice in the beaker (half full)‚ and a known amount of salt in another beaker 3. Measure the temperature (melting point) of the ice without adding any impurity (salt). 4. Measure the temperature (melting point) of the ice after adding the salt into the beaker. 5. Heat up
Premium Water Solid Fahrenheit