EXPERIMENT: 1 Object: To find the wavelength of Sodium light by Newton’s ring. Apparatus required: A Plano convex lens of large radius of curvature‚ optical arrangement for Newton’s rings‚ plane glass plate; sodium lamp and traveling microscope. Formula used: The wavelength of light is given by the formula λ =D n2+p –Dn2 / 4pR Where D n+p = diameter of (n+p)th ring Dn = diameter of n th ring‚ P = an integer number‚ R = radius of curvature of the curved face of the Plano- convex lens.
Premium Light Wavelength Angle
Equipment’s: 1) Vernier caliper 2) Triple beam balance 3) Steel cube 4) Cylinder including (Aluminum‚ brass‚ copper) Theory: The goal of the first part of this experiment is to determine the densities of a number of cylinders‚ and gain an understanding of how different measurement techniques can affect the reliability of experimental results. Procedures: We measured the length‚ mass‚ and density of the brass‚ copper and aluminum wires with a venire caliper in millimeter‚ the mass with
Free Measurement Volume Uncertainty
Case Study 1: Blozis Company Emily Bowers MKTG 444: Supply Management Statement of Problem: The president of Blozis Company must find a way to unify communications between the supply‚ engineering‚ and production departments on setting up standard requirements for keeping better track of ordering and sending out materials to suppliers. Background: Overdue payments on materials that have been received by Blozis Company-no receiving
Premium Management
1. There are two main types of cells‚ prokaryotic and eukaryotic. The connection between the two can be seen right from their prefixes‚ pro meaning before and eu meaning true or good. This is because prokaryotic cells are before a nucleus and eukaryotic cells possess a true nucleus. This has led to many theories that eukaryotic cells have evolved from prokaryotes. The evidence for this is most noticeable in the structure of the cells‚ which will be compared below. Prokaryotic cells have no
Free DNA Bacteria Eukaryote
400667 8” Vernier Calipers S/N: 3475 9.97” x 1.0” x 0.123”Aluminum Beam Steel Reference Beam with (6) drilled measuring holes C-Clamp Shim Figure 1: Side View of Experimental Set-up Experimental Procedure 1. The three piece beam arrangement shown in Figure 1 was clamped to a table. 2. The following distances were measured: a. Edge of table to the end of the steel reference beam using calipers. b. Edge of table to center of mass hanger using calipers. c. Top of steel beam
Premium Experiment Measurement Cantilever
Experiment 5: RC Circuits Abstract The purpose of this lab is to learn and understand RC Circuits. An RC circuit is composed of at least one resistor and at least one capacitor. A capacitor is composed of two plates with either air or an insulator also known as a dielectric between the plates. We do not want the plates to be touching‚ because then we would only have a conductor. The insulator between the plates is also known as the dialectic‚ which affect how the capacitor will store
Premium Capacitor RC circuit Electric charge
were used in the experiment: One (1) aluminum sample rod One (1) steel rod One (1) brass rod Roll of thermal tape Candle Stopwatch The following laboratory equipment was required: One (1) clamp stand A set of calipers 3. Procedure Initial Setup Using the calipers‚ the diameter of each sample rod was measured and recorded. The each sample rod was individually attached to the clamp stand. After attaching the rod to the clamp stand candle wax was poured to one end of the rod. In order
Premium Heat Temperature Heat transfer
density with reported values. In Exercise 2‚ you will determine the density of pennies by water displacement. B. Procedures Exercise 1. Density of A Regular Solid Apparatus: Electronic balances‚ beakers‚ regular-shaped solids‚ vernier calipers Safety Equipment: aprons‚ goggles Chemicals: None Objectives: In this exercise you will: 1. learn to operate the electronic balance properly to measure the mass of an object. 2.
Premium Density Volume Copper
Measurement: Length‚ Mass‚ Volume‚ Density‚ and Time Peter Jeschofnig‚ Ph.D. Version 42-0267-00-02 Lab Report Assistant This document is not meant to be a substitute for a formal laboratory report. The Lab Report Assistant is simply a summary of the experiment’s questions‚ diagrams if needed‚ and data tables that should be addressed in a formal lab report. The intent is to facilitate students’ writing
Premium Volume Measurement Density
Gather the proper tools needed to replace your brake caliper. Socket set Brake line wrench set Drop light Screwdrivers set Needlenose pliers Torque Wrench Gloves and goggles Brake fluid Car jack Service manual how to replace a brake caliper on your vehicle if needed go to the parts store and get a two ton jack minimum. So that way you can jack up your tire on which side you are needing to work on. You would need to place it right under the coil over .After you have jacked up the tire:follow
Premium Automobile Wheel Tire