In part A of the experiment the two values obtained for the specific heat capacity of the metal were about .0500 J/mol. This is a large deviation‚ with both of these values identifying very different metals. The average heat capacity identified the metal used as brass. The average heat capacity calculated was .3776 J/mol and the actual heat capacity of brass is .375 J/mol. The second run displayed the closest value to the actual value. A source of error that may have caused a large divide in the
Premium Chemistry Water Acid
physics and chemistry‚ heat is energy transferred from one body to another by thermal interactions. The transfer of energy can occur in a variety of ways‚ among them conduction‚radiation‚ and convection. The SI unit of heat is the joule. Heat can be measured by calorimeter‚ or determined indirectly by calculations based on other quantities‚ relying for instance on the first law of thermodynamics. In calorimeter‚ the concepts of latent heat and of sensible heat are used. Latent heat produces changes of
Premium Temperature Energy Thermodynamics
Comparing the enthalpy changes of combustion of different alcohols Aim In this experiment I will investigate the enthalpy changes of combustion. In particular I will be investigating the enthalpy change of combustion for different alcohols. I hope to investigate some of the homologous series alcohols‚ as well as a few structural isomers of these alcohols. Background & theory Enthalpy cannot be measured. What we can actually measure is the enthalpy change from the reactants to the products.
Premium Ethanol Energy Enthalpy
Internal Combustion Engines Introduction Internal Combustion Engine‚ a heat engine in which the fuel is burned ( that is‚ united with oxygen ) within the confining space of the engine itself. This burning process releases large amounts of energy‚ which are transformed into work through the mechanism of the engine. This type of engine different from the steam engine‚ which process with an external combustion engine that fuel burned apart from the engine. The principal types of internal combustion
Premium Internal combustion engine Diesel engine
HEAT GENERATED IN APPLIANCES Why do some appliances produce more heat than the others? Most appliances with high power rating are heating appliances.The heating appliances has a heating element like resistors. The resistorsconvert electrical energy into light and thermal energy . It depends on the resistance of material if how much heat can be produced from electricity. Those devices who produced heat‚ the Nichrome wire is an element who is responsible for heating . when we say nichrome
Premium Energy Incandescent light bulb Heat
Post-Lab Report for Experiment 2: Cooperative Identification of an organic Solid October 6‚ 2013 Introduction: This experiment was focused on the cooperative identification of organic compound by its chemical properties such as: slow melting point‚ mixed melting point‚ Rf values in TLC experiment‚ IR spectrum analysis‚ and H NMR spectra. Such data can provide the the identity of functional groups and the identity of the compound itself. In this experiment
Premium Nuclear magnetic resonance Spectroscopy Chemistry
Internal Combustion Engines An internal-combustion engine is a heat engine that burns fuel and air inside a combustion chamber located within the engine proper. Simply stated‚ a heat engine is an engine that converts heat energy to mechanical energy. The internal- combustion engine should be distinguished from the external- combustion engine‚ for example‚ the steam engine and the Stirling engine‚ which burns fuel outside the prime mover‚ that is‚ the device that actually produces mechanical
Premium Internal combustion engine
relationship between the mass of magnesium and mass of oxygen once the magnesium has been heated and reacted with the oxygen. There will be 3 variables in this experiment. The independent variable will be the mass of magnesium ribbon as different measurements will be taken and used for each trial. The dependant variable will be the mass of Magnesium Oxide‚ this is a measured variable as the mass of oxygen can be calculated and will enable us to determine the formula for Magnesium Oxide. The controlled variable
Premium Measurement Magnesium oxide Oxide
5 2.2 Essential Feature of combustion process 6 2.3 Stages of Combustion in CI engine 7 2.4 Combustion phenomenon in CI Vs SI engine
Premium Internal combustion engine Diesel engine
XV. GIMNAZIJA International Baccalaureate Department Group 4 – Chemistry SL Lab no.2: Acid-base titration Student: Caterina Rende Dominis Teacher: Zrinka Toplićan Date: 19 November 2012 Data Collection and Processing (DCP) Aspect 1: Recording raw data Table 1 Table showing raw data collected from titration Known measurements 25 mL of diluted acid 0‚100 M of NaOH solution Measurement Number | V of alkali needed to neutralize acid /mL/ (±0.01 mL)
Premium Sodium hydroxide Base