AP Chemistry Kinetics Lab Abstract: The purpose of this lab is to learn how to write law expressions‚ determine orders by graphs‚ and calculate rate constants. By determining the number of drops of sodium hypochlorite necessary to make a diluted food dye change to colorless in less than three minutes helps calculate the absorbance which can then be analyzed to find the pseudo rate constant and eventually leading to the rate constant and the rate law. The results show that the m and n are both 1st
Premium Chemistry Chemical reaction Reaction rate
Organic Chemistry II Lab 9 Fermentation of a Carbohydrate: Ethanol from Sucrose * Introduction Ethanol is one of the oldest alcohols and also the least toxic one. Industrially‚ ethanol is made most economically by hydration of ethylene. However‚ ethanol that is intended for human consumption must‚ by law‚ be prepared by fermentation. By either method‚ ethanol‚ of course‚ has the same formula‚ structure‚ and properties. The fermentation takes place with the assistance of enzymes from yeast
Premium Ethanol Glucose Carbon dioxide
Institute Physics Course 2014 - Rocket Lab Report Title: RockSim and Electronic Altimeter Measurement Techniques Name: Scarlet Henriquez Email: scarletpatricia94@aol.com LAB SESSION ___8____Assignment _____7_____ Due Date: ___7/8/14______ Objective: Launch a smaller rocket to learn how to compare RockSim predictions (computer based) to an actual instrument measurement carried by the rocket (Electronic Altimeter). This Lab shows how better the electronic measurement
Premium Rocket Mathematics Flight
Lab Report 3 In this lab‚ we will take a trip to the planetarium lab and will learn about Right ascension and declination‚ and altitude and zenith. After looking at the different points shown‚ we will log the altitude and zenith in the chart in our lab manual. Now we will look at the same points and label the right ascension and declination. Then we will learn about the easiest way to locate the star Polaris. As we started the first program‚ we answered a few questions to make sure we knew
Premium
This lab report will be detailing the steps taken and the results discovered when using spectrophotometry to determine the percentage of copper in a copper-clad penny and the thicknes of the copper layer on the copper-clad penny. After 1982‚ copper coating has been used in the creation of the penny because the cost of pure copper has increase to the point that the amount needed t omake a penny cost far more than the actual value of the penny. This lab allowed us to see just how much copper coating
Premium Chemistry Spectroscopy Ammonia
TITLE OF EXPERIMENT 2 : DILUTION 2.1: OBJECTIVES Upon completion of this experiment‚ students should be able to: 1. determine the concentration of coloured solution such as FeCl3 by using dilution and colour differentiating (colorimetric) techniques. 2.2: INTRODUCTION Concentration can be expressed in many different ways such as percentage volume and percentage weight etc. In laboratory‚ normally concentrations were expressed as molarity and normality. Molarity is the
Premium Concentration Chemistry
…………………………………………………………………………. 12 Chemical Changes Experiment 3 …………………………………………………………………………. 15 Classification of Matter Experiment 4 ………………………………………………………………………….17 Chemical Nomenclature: The Language of Chemistry Experiment 5 ………………………………………………………………………….22 Water of Hydration Experiment 6 ………………………………………………………………………….25 Gases Experiment 7 ………………………………………………………………………….27 Oxygen Experiment 8 …………………………………………………………………………
Premium Chemistry Laboratory glassware Sodium chloride
Group No.___ Date Performed :___________ Chemistry Laboratory 101__ Date Submitted[1] :___________ Members[2]: Instructor’s Initials[3] :___________ 1. _____________________ 2. _____________________ 3. _____________________ 4. _____________________ Laboratory Report Sheet The Bunsen Burner Activity 1 Objectives:4 1. ________________________________________________________ 2. ________________________________________________________
Premium Laboratory equipment Question Knowledge
MEC 325/580 Lab Report CNC Machining Lab Report Date: March 18‚ 2013 Group Leader: Jian Wu Team Members: Group Number: G4 Regment No.: D Insturctor: CONTENTS 1.Objective and introduction. 2.Principles and practice. 3.Design and result. 4.Conclusion and recommendations. Appendices 1. Objective and introduction * Objectives Operate the CNC milling machine using G-codes‚ M-codes in a CNC program. * Equipment: Minitech CNC machine (Series 2) * Machine
Premium Milling machine Numerical control
LAB REPORT Introduction: In a chemical change‚ the identities of substances change and new substances form. In an equation the substances on the left are the reactants. The substances on the right are the products. In this experiment the objectives are to observe evidence that a chemical change has taken place. Infer from observations that a new substance has been formed. Identify and record observations that show energy is involved in chemical change observe the color‚ solubility of some substances
Premium Chemical reaction Chemistry Hydrogen