Jashandeep Gill Gammellos Chemistry Density is one of the fundamental principles of physics. Density is the reason why a plank of wood floats on water while a piece of metal several times smaller will sink. Density of an object is measured in g/cm³ or g/cc. The equation is D=M/V‚ D being the density of the object‚ M being the mass of the object‚ and V being the volume of the object. Mass is the space an object takes up. It is the amount of matter present in an object. Mass is measured using
Free Density Water Kilogram
Procedure Access the virtual lab and complete the experiments. Part One (Flame Test): 1. Create and complete a data table for Part One of the lab. It should include the name of the element (or unknown) examined and the color of the observed flame: Barium-green Calcium-red Sodium-yellow Rubidium-purple Potassium-blue Lithium-pink 2. Identify each unknown from Part One of the lab and briefly explain why you identified each unknown as you did.: Unknown 1-yellow. I think it is Sodium because
Premium Light Atom Color
Physical and Chemical Change Objective: Recognize and distinguish between chemical and physical changes. Materials: - lab balance - microspatula - lab burner - dropper pipet - 5 test tubes - mortar and pestle - test tube rack - magnet - test tube holder - insulating pad - watch glass - safety goggles - glass square - lab apron or coat - copper sulfate pentahydrate - iron fillings - sodium chloride - magnesium ribbon - hydrochloric acid - paper
Premium Chlorine Mixture Sulfuric acid
Regents Chemistry Quarter 1 Midterm Review 1. The percent by mass of oxygen in Na2SO4 (formula mass = 142) is closest to 1) 11% 3) 45% 2) 22% 4) 64% 2. Given the unbalanced equation: __Al(s) + __O2(g) → __Al2O3(s) 3. 4. 5. 6. 7. balance the equation using smallest whole number coefficients. The percent by mass of aluminum in Al2O3 is approximately 1) 18.9 3) 47.1 2) 35.4 4) 52.9 What is the approximate percent composition by mass of CaBr2 (formula mass = 200)
Premium Water Ideal gas law Melting point
Discussion The purpose of the Density Lab was to determine the identity of four unknown solids and two unknown liquids by calculating their densities and comparing them to a density chart‚ taking into account error analysis and finally classifying the substances. In order to calculate this density‚ we first found the mass of the container that was to be holding the substances. We then found the volume of the substance‚ and lastly determined the mass of the container and substance. We subtracted
Premium Liquid Density Volume
IB Chemistry - Internal Assessment Lab Format The following titles and subtitles should be used for your lab report and given in this order within your lab report. Use the following sheet as a checklist when writing lab reports. Each lab report may focus on different sections so be sure that you are focusing on the section(s) that the lab is addressing. Introduction A short paragraph explaining to the reader what was performed during the experiment. Include diagrams‚ if appropriate. Design Research
Premium Measurement Uncertainty Mathematics
Chemistry Lab Report (Design) Factors affecting Rates of a Reaction (Kinetics) KINETICS DESIGN LAB Research Question: Does the concentration of Potassium Iodide (KI) affect the rate of its reaction with hydrogen peroxide (H2O2) (of a fixed concentration)? Introduction: There are several factors that affect the rate of a reaction. Some of them being Pressure (if the reactants are Gases)‚ Temperature‚ Presence of a Catalyst‚ Surface Area of the reactant‚ and Concentration. According to
Premium Hydrogen peroxide Sodium Chemical reaction
9/19/2012 Experiment #1-Density Aim: Learn how the process of distillation occurs. Observe how distillation separates alcohol from wine. Method: Distillation is based on the fact that the matter can exist in three phases - - solid‚ liquid and gas. As the temperature of a pure substance is increased‚ it passes through these phases‚ making a transition at a specific temperature from solid to liquid (melting point--mp) and then at a higher temperature from liquid to gas (boiling point--bp). Distillation
Premium Distillation Water Evaporation
DESIGN LAB Factors Affecting the Solubility of a Solid in a Liquid In this experiment‚ my goal is to determine the affect of temperature in the solubility of a solid in a liquid. Research Question: How does the change in the temperature affects the solubility of a solid in a liquid? Independent variables: Temperature of the Solution Dependent variables: The solubility of the solid substance Controlled Variables: * The pressure of the room. * The mass of zinc chloride
Free Solid Liquid Water
Maggie Mitchell IB Chemistry Prd. 5 THE HALOGENS LAB Date: 9/11/13 Purpose: The purpose of this experiment was to observe and record the halogens’ (NaF‚ NaCl‚ NaBr‚ and KI) reactions with the chemicals Ca(NO3)2‚ AgNO3‚ and NH4OH and use these observations to identify an unknown halogen. Data: (see next page) TABLE 1: REACTIONS OF HALOGENS WITH CA(NO3)2‚ AGNO3‚ AND NH4OH REACTION NAF NACL NABR KI REACTION W/ CA(NO3)2 solution turns cloudy and precipitate forms clear precipitate
Premium Chlorine Periodic table Chemical element