October 13‚ 2012 Needle through a Balloon Pre-Lab Preparations: Purpose: The purpose of this experiment is to see if the balloon pops when pierced with a wooden skewer or a sharp pin. Hypothesis: If we lubricate the skewer with petroleum jelly‚ then it should go through the balloon without popping. Hypothesis for the 2nd part of the Lab: If we cover the side of the balloon with cellophane tape‚ then it will not pop when pierced with the pin. Materials: • Balloons • Long wooden
Premium Hypothesis Observation Stanford prison experiment
Jashandeep Gill Gammellos Chemistry Density is one of the fundamental principles of physics. Density is the reason why a plank of wood floats on water while a piece of metal several times smaller will sink. Density of an object is measured in g/cm³ or g/cc. The equation is D=M/V‚ D being the density of the object‚ M being the mass of the object‚ and V being the volume of the object. Mass is the space an object takes up. It is the amount of matter present in an object. Mass is measured using
Free Density Water Kilogram
Procedure Access the virtual lab and complete the experiments. Part One (Flame Test): 1. Create and complete a data table for Part One of the lab. It should include the name of the element (or unknown) examined and the color of the observed flame: Barium-green Calcium-red Sodium-yellow Rubidium-purple Potassium-blue Lithium-pink 2. Identify each unknown from Part One of the lab and briefly explain why you identified each unknown as you did.: Unknown 1-yellow. I think it is Sodium because
Premium Light Atom Color
Physical and Chemical Change Objective: Recognize and distinguish between chemical and physical changes. Materials: - lab balance - microspatula - lab burner - dropper pipet - 5 test tubes - mortar and pestle - test tube rack - magnet - test tube holder - insulating pad - watch glass - safety goggles - glass square - lab apron or coat - copper sulfate pentahydrate - iron fillings - sodium chloride - magnesium ribbon - hydrochloric acid - paper
Premium Chlorine Mixture Sulfuric acid
Discussion The purpose of the Density Lab was to determine the identity of four unknown solids and two unknown liquids by calculating their densities and comparing them to a density chart‚ taking into account error analysis and finally classifying the substances. In order to calculate this density‚ we first found the mass of the container that was to be holding the substances. We then found the volume of the substance‚ and lastly determined the mass of the container and substance. We subtracted
Premium Liquid Density Volume
Conclusion The purpose of this experiment was to discover the chemical properties that copper has when reacting with other chemicals and how it changes physically during these processes. (Department of Chemistry‚ 2013) This was achieved through many types of reactions‚ such as a redox reaction‚ double displacement‚ decomposition reaction and single displacement depending on the chemical properties in relation to copper of the other substances when it was added with copper. Copper was either in an
Premium Chemistry Chemical reaction
1: The data was collected from the lab experiment. Sample calculations are shown. Mass of beaker with sample 30.765g Mass of empty beaker 30.263g Mass of sample .502g Mass of beaker with sample after 1st heat 30.661g Mass of beaker with sample after 2nd heat 30.657g Heating mass difference .004g Mass of anhydrate .394g Mass of H2O .108g Molar mass of CuCl2 135.0g/mol Molar mass of H2O 18.0g/mol Moles of anhydrous sample 2.92x10-3 moles CuCl2 Moles of H2O released 6.00x10-3
Premium Mathematics Mole Heat
TITLE: THE EFFECT OF HEATING DIFFERENT SUBSTANCES INTRODUCTION: In this exercise‚ it was required to observe carefully what happened when certain substances were heated in a burner‚ and to note the appearance of the residue after heating. AIM: To observe the effects of heating different substances. MATERIALS: Hard glass test tubes Powered samples of Lead (II) nitrate Copper (II) sulphate Ammonium chloride Zinc sulphate Basic copper (II) carbonate‚ CuCO3. Cu(OH)2
Premium Gas Copper Sulfuric acid
He a lt h 0 3 2 3 Fire 0 Re a c t iv it y 2 P e rs o n a l P ro t e c t io n Material Safety Data Sheet Sulfuric acid MSDS Section 1: Chemical Product and Company Identification Product Name: Sulfuric acid Contact Information: Catalog Codes: SLS2539‚ SLS1741‚ SLS3166‚ SLS2371‚ SLS3793 CAS#: 7664-93-9 Sciencelab.com‚ Inc. 14025 Smith Rd. Houston‚ Texas 77396 RTECS: WS5600000 US Sales: 1-800-901-7247 International Sales: 1-281-441-4400 TSCA: TSCA
Premium Sulfuric acid Oxygen Chlorine
9/19/2012 Experiment #1-Density Aim: Learn how the process of distillation occurs. Observe how distillation separates alcohol from wine. Method: Distillation is based on the fact that the matter can exist in three phases - - solid‚ liquid and gas. As the temperature of a pure substance is increased‚ it passes through these phases‚ making a transition at a specific temperature from solid to liquid (melting point--mp) and then at a higher temperature from liquid to gas (boiling point--bp). Distillation
Premium Distillation Water Evaporation