CHEM/ENCH 212 EXPERIMENT II: KINETICS OF NUCLEOPHILIC SUBSTITUTION DATE OF SUBMISSION: Table of Contents Experimental Table : Hazardous properties of chemicals used in the experiment.[1] Acetone Irritant. Do not inhale vapors. Highly flammable. 2 chloro‚ 2 methyl propane Flammable. Equipment 1. Conductivity probe 2. Constant temperature water circulation bath 3. Stir-plate with stirring magnets
Premium Chemistry Chemical reaction Oxygen
the heads of the claisen adapter. A rubber septum was then added to the other head and the entire apparatus is placed on a hot plate at its lowest setting. Meanwhile‚ 20 ml of anhydrous diethyl ether was added to a 50 ml Erlenmeyer flask and sealed using a rubber septum.
Premium Chemistry Water Solvent
ab reportChemistry 117L Laboratory Report Name: Aneesa Noorani Lab Day: Tuesday Lab Room: SCL 114 Date of Experiment: January 22‚ 2013 TA: Mikhail 1. Basic Laboratory Skills Purpose(s) of the Experiment: The purpose of the first part of today’s experiment is to establish the stoichiometry of the reaction between titrate oxalate (C2O42-) and permanganate (MnO4-). The purpose of the second part of today’s experiment is to learn about the concepts of the rate of chemical reactions
Premium Titration Mole
ions in hydrochloric acic and colour changes of indicators 2.To determine standard solutions and the unknowns Variables Independent variable : Concentration of hydrogen ions in hydrochloric acid.The presence of hydrogen ions is varied by using 5 different concentration of hydrochloric acid of 0.1mol/L‚0.01mol/L‚0.001mol/L‚0.0001mol/L‚0.0000mol/L Dependent variable : Colour changes of indicators.The colour change of indicators in unknown 1 and unknown 2 can be observed by comparing with
Free PH Hydrochloric acid PH indicator
Purpose: To find out the densities and to find out the name of the unknown metals. (Based on the extensive and intensive properties) Check up the words mass‚ volume‚ density‚ extensive properties‚ and intensive properties. Where do the units for mass and volume) come from and what do they mean? What is the density of distilled water? What is Archimedes principle? Does temperature affect the density of a solid? Liquid? Gas? Materials: Safety glasses‚ 10‚ 25 or 50 mL graduated cylinders
Premium Water Liquid Density
Experiment 3: ANALYSIS OF UNKNOWN ACID SAMPLE USING TITRATION METHOD Date of Experiment: 4 September 2012 Introduction An acid-base titration is a procedure used in quantitative chemical analysis to determine the concentration of either an acid or a base. Titration is the slow addition of an acid (or a base) of known concentration from a burette (a narrow graduated cylinder) to a base (or an acid) of unknown concentration fin an Erlenmeyer
Premium Titration Sodium hydroxide
Table 8.1- Combustion of magnesium ribbon Observations Reaction was exothermic; magnesium ribbon burned and was glowing a bright white color when ignited. Reactants: Mg and O2 Products: MgO Balanced chemical equation 2Mg + O2 2MgO Table 8.2- Combustion of heptane Observations When holding test tube inverted over heptane flame‚ condensation formed against top walls of the test tube. When the burning splint was added the walls of the test tube became less foggy from the condensation
Premium Chemical reaction Carbon dioxide Sulfuric acid
CHEM 113L EXP# 7: Buffer Preparation and pH Measurements Revised . AMB 7-2005 Introduction: Even in quite dilute aqueous solutions‚ acetic acid is very slightly ionized (it would approach 99% ionization only as the concentration approaches 0.0 M): HC2H3O2(aq) + H2O(l) Ka = 1.8 x 10-5. H3O+ + C2H3O2- In general‚ if the acid is not extremely weak‚ the pH of a solution of a weak acid is governed by the concentration of the acid and Ka. Under similar conditions‚ the pH of a solution of a weak base
Premium Acetic acid PH Buffer solution
Buffer Post Lab Calculation 1. We added too much NaOH to our buffer 1 solution. The original pH was 5.32‚ with 10mL of buffer and 10mL of DI water. We added 5mL of NaOH and the pH changed to 12.12. If 5 mL changed the pH by about 7‚ then we predict that about 2 mL of NaOH would change the pH by about 2. This prediction is based on the fact that 2.5mL is half of 5mL‚ and 3.5 is half of 7‚ so adding a little less than 2.5mL would give us a difference of about 2. For the buffer 2 solution‚ the original
Premium
The human blood buffer response to increased amounts of acids and bases was determined by titration of a 25.00 mL sample of H2PO4 buffer solution with 0.1 M HCl and 0.1 M NaOH. The volume of 0.1 M HCl is about double of the amount 0.1 M NaOH used to lower/raise the pH of a blood buffer. In this experiment‚ HCl (a strong acid) and NaOH (a strong base) are used as examples of strong acids/bases‚ and the titration with H2PO4 shows the effect on a buffer solution. The assumption was the addition
Premium PH Acid