Standardize a solution of potassium manganate(VII) by an iron (II) salt (ammonium iron (II) sulphate) Introduction Oxidation numbers describe the number of electrons the atom will gain or lose during a reaction. Each atom in an equation can be assigned an oxidation number according to certain rules. If the oxidation number of an atom increases as you go from the left side to the right side if an equation‚ oxidation has occurred (electrons have been lost); if the oxidation number decreases
Premium Potassium permanganate Manganese Oxidizing agent
Chemistry 3373F Lab Manual 2008 Modified 11/07 Table of Contents Chem 3373 Laboratory Schedule for Fall 2008.............................................................................2 The Benzoin Condensation of Benzaldehyde ..............................................................................3 Synthesis of Dilantin and Related Compounds (two weeks).........................................................6 Synthesis of an Alkaloid: Pseudopelletierine (two weeks) .............
Premium Hydrochloric acid Sulfuric acid Acetic acid
CHEM 1211 L Principles of Chemistry Lab 16 February 2004 Lab Report 1 Introduction The purpose of this project is to identify an unknown organic acid (X) by conducting various experiments to determine the acid’s unique properties. By determining selected constant properties of the unknown and then comparing these properties to the constant properties of known substances‚ it is possible to identify an unknown substance. The properties used to identify the unknown must be intensive‚ or independent
Premium Chemistry Chemical reaction Oxygen
Table 1: Data Collection Table – Contains all of the primary data directly obtained from the lab. Indicator | Initial volume of NaOH in burette (ml) ±0.05 | Final Volume of NaOH in burette (ml) ±0.05 | Final – initial Burette Reading (Volume of NaOH used) (ml) ±0.1 | Qualitative Observations | Phenolphthalein | 0.00 | 0.90 | 0.9 | At first when the base was being dropped into the vinegar there wasn’t a color change‚ however when the solutions came close to full titration‚ the solution
Premium PH indicator Sodium hydroxide Titration
CunananProfessor Stewart Chemistry 400 T/TH 1:30 PM 18 March‚ 2014 Objectives: In this Experiment‚ we will be decomposing KClO3 into two different compounds‚ KCl and O2. We are given a known mixture that has MnO2 in it to act as a catalyst. When decomposing KClO3 it releases O2 gas‚ which we then collect into the Erlenmeyer flask. The gas then displaces the water into the beaker‚ which we can then calculate the water evolved. The first method we use to determine the percent composition is Gravimetric
Free Gas Pressure Chlorine
Chemistry Lab Report 1 Nicole H. Healey (Experiment 1 and 2) October 7‚ 2014 Data Collection: Table 1: (First Titration) C2O42- Analysis Sample 1 Sample 2 Molarity of KMnO4 0.02m 0.02m Weight of Sample 0.237g 0.225g Final Buret Reading 28.5ml 26.3ml Initial Buret Reading 0ml 0ml Volume of KMnO4 dispensed 28.5ml 26.3ml Moles
Free Titration Potassium permanganate Mole
Chemistry Laboratory 6A – Stoichiometric Analysis of an Iron-Copper Single Replacement Reaction Martin Sun Purpose The purposes of this experiment were to: determine the number of moles of iron reacted; determine the number of moles of copper produced; and calculate the ratio of moles of copper to moles of iron. Materials and Methods Materials and methods for this laboratory followed those laid out in Experiment 6A on pages 56-59 of Essential Experiments for Chemistry by Morrison and Scodellaro
Free Iron Chemical reaction Chemistry
Moles of Iron and Copper Lab Data and Observations Before the reaction: Mass of empty‚ dry beaker: 153.44g Mass of beaker + copper (II) chloride: 161.44g Mass of two iron nails: 7.27g After the reaction: Mass of two iron nails: 6.29g Mass of beaker + copper (dry): 154.50g Questions and Calculations 1. a) Mass of two iron nails before the reaction – Mass off two iron nails after the reaction = Mass of iron used in the reaction = 7.27g – 6.29g = 0.98g
Premium Chemistry Atom
Chemistry design: Fuel energy lab Research question: What is the energy density of cyclohexane‚ and how does it compare to the energy density of normal hexane? Variables: Independent variable – The independent variable in this experiment will be the type of fuel that will be used. This will be either Hexane or Cyclohexane. Each type will be given to us and labelled so it will be quite simple to control this variable. This cannot be measured using any apparatus so the lab assistant must be entrusted
Premium Heat Temperature Energy
Chemistry Lab Report on standardization of acid and bases. Purpose: To prepare standardize solution of sodium hydroxide and to determine the concentration of unknown sulfuric acid solution. Data and Calculations: This experiment is divided into two parts (Part A and Part B). In the first part of experiment‚ the standardize solution of sodium hydroxide is prepared by titrating it with base Potassium hydrogen phthalate (KHP). The indicator Phenolphthalein is used to determine that whether titration
Premium Sodium hydroxide