McLean 1 Creating Acetylene Gas Introduction The purpose of the lab was to determine the ratio of air to acetylene results in complete combustion of acetylene gas. The balanced chemical equation for this experiment was C2H2(g) + O2(g) --> CO2(g)+ H2O(l). Complete combustion is the reaction of an element or compound with oxygen to produce the most common oxides and energy. Complete combustion occurs when the fuel and oxygen combine in exact proportions to completely burn the fuel
Premium Oxygen Combustion
Dalton Leach Physics 2 lab chapter 21 6/26/2015 Procedure Part I Wire Resistance: As wire length (cm) increases‚ the resistance (Ω) increases As wire area (cm2) increases‚ the resistance (Ω) decreases As wire resistivity (Ωcm) increases‚ the resistance (Ω) increases Procedure Part II: Ohm’s Law: Electricity‚ Magnets‚ and Circuits Ohm’s Law mA is milliamps‚ and 1000 milliamps equals one Ampere. Move the potential (volts) and resistance (ohms) sliders and observe the current (amps) As voltage
Premium Volt Incandescent light bulb Electric current
Morgan Land Elizabeth Hollis Physics II February 7‚ 2012 Electric Fields Lab Abstract: In this lab we will study the equipotential lines in an electric field in order to study the structure of the electric lines of force. We will plot the position of electric field lines in a given electric field using both a manual method and a computer software program. There is an electric field in any
Premium Electric charge Electromagnetism Magnetic field
One of the main learning experiences of this lab is to learn the importance of calibrating a sensor. In most cases‚ a sensor will not have an output that is exactly what you need. An example of this is a strain gage. A stain gage gives back a voltage‚ but with that given voltage a distance can be found. Introduction: In this experiment‚ the QNET-MECHKIT was used. This board has multiple compact sensors that can be used for experiments. For this lab we will be using the strain gage to find the
Premium Metrology Measurement Angle
Nervous System lab was designed to measure reaction times by using a variety of tests that affect the heart rate. These tests were the startle‚ stroop‚ Valsalva maneuver‚ diving reflex‚ and a test of our choice. The test our group chose to measure the heart rate in response to doing a trust fall to anticipate the stress right before the fall. To begin this lab we chose a participant‚ and then hooked their finger up to the pulse transducer sensor. Using the chart 5 program on the lab computer the participant’s
Premium Parasympathetic nervous system Autonomic nervous system Peripheral nervous system
and Ohm’s Law Go to http://phet.colorado.edu/simulations/sims.php?sim=Ohms_Law and click on Run Now. Wire Resistance and Ohm’s Law Procedure Part I Wire Resistance: open the PhET Simulation Electricity‚ Magnets‚ and Circuits Resistance in a Wire. As wire length (cm) increases‚ the resistance (Ω) ___increases____ As wire area (cm2) increases‚ the resistance (Ω) ___decreases___ As wire resistivity (Ωcm) increases‚ the resistance (Ω) ____increases__ Procedure Part II: Ohm’s Law: Electricity
Premium Incandescent light bulb Volt Electric current
LSM1102 Lab Report Introduction Transformation is a process which involves plasmid DNA being bound to the cell surface and the subsequent uptake of DNA by the cell (Panja et al.‚ 2008). For artificial transformation of E. coli cells with plasmids‚ plasmid DNA has to be extracted from bacterial cells using the High-Speed Plasmid Mini Kit‚ which is then mixed with competent E. coli cells followed by heat shock and the streaking of transformed cells on two different types of agar plate (LB and LB+ampicillin)
Premium Plasmid Transformation Escherichia coli
PRE LAB REPORT Reynaldo Riboul TLC and Column Chromatography October 6‚ 2013 Table of Chemicals: Chemical Hazards Mol. Wt. Density Grams Moles Acetone Flammable‚ Irritant 58.08 g mol−1 0.791 g cm−3 2.0 g 0.0344 Hexane Flammable‚ Irritant‚ Dangerous to Environment 86.18 g mol−1 .6548 g mL−1 9.0 g 0.1044 Fluorene Very toxic to aquatic life with long lasting effects 166.223 g/mol 1.202 g/mL 0.3 g 0.00180 Fluorenone Irritant 180.20 g mol−1 1.13 g/cm3 0.3 g 0.00166
Free Solvent Oxygen Laboratory glassware
Lab Report – Strong Example Problem/Question Does using a base coat before painting nails prevent chipping? Background Information When painting nails‚ some manicurists use a base coat before applying the polish. The purpose of a base coat is to help the polish stick to your nails more easily. Base coats also help to protect your natural nail from the staining effects of colored polishes. Ridge-filling base coats fill in the grooves and cracks in the nail to create a smoother appearance
Premium Left-handedness French Revolution Handedness
Lab 17 Amino Acids and Proteins Lab date 10/22/2013 12-1350 I Purpose The purpose of this experiment was to separate mixtures of II Method For a complete list of experimental procedures see prelab outline attachment #1. “For a complete list of experimental procedure see Seager‚ Spencer L. and Slabaugh‚ Michael R. Safety-Scale Laboratory Experiments for Chemistry for Today General‚ Organic and Biochemistry; Thomson Brooks/Cole‚ Belmont‚ CA‚ USA‚ 2008; pp.221-225”. III Data Part A Mass
Premium Experiment Chemistry Cholesterol