Polymer Essay: Plexiglass Many of the glass screens and windows we see today are not really made of glass. They are made of plexiglass. Plexiglass is not related to the chemical structure of glass at all. It is an organic polymer. Today this polymer is used in all sorts of applications. The formation of plexiglass was begun in 1930‚ at McGi11 University by William Chalmers‚ a research student. He polymerized methacrylic ethyl ester and methacrylic nitirile‚ creating a clear plastic paste
Premium Polymer Glass Temperature
temperature where the lowest melting constituent of steel starts to melt. The strength decreases and looses plasticity and tind to crumble under applied stress instead of flow. 2. Selection of temperature depends on a) Chemistry. b) Melting point of the lowest constituent. 3. Finishing temperatures. Lower the finishing temperature finer the structure of the piece but limited to mass and shape. The finishing temperature should be near the lower transformation point. SCALING 1. Not
Premium Steel Forging Melting point
Physics Facts & TriviaA rubber band shrinks when heated and expands when cooled because of the change in its Entropy state.Submitted by: Emily (Awesome) - Helena‚ Montana‚ United StatesDue to the effect of Thermal Expansion‚ the Eiffel Tower is upto 15cm taller in summer.Submitted by: Muhaimin Mareum Khan - Dhaka‚ BangladeshRadar is an abbreviation ofRadio Detection And Ranging.Submitted by: Marvin Jadulos - PhilippinesIf an atom were the size of a stadium‚ its electrons would be as small as
Premium Oxygen Temperature Earth
Regents Chemistry Quarter 1 Midterm Review 1. The percent by mass of oxygen in Na2SO4 (formula mass = 142) is closest to 1) 11% 3) 45% 2) 22% 4) 64% 2. Given the unbalanced equation: __Al(s) + __O2(g) → __Al2O3(s) 3. 4. 5. 6. 7. balance the equation using smallest whole number coefficients. The percent by mass of aluminum in Al2O3 is approximately 1) 18.9 3) 47.1 2) 35.4 4) 52.9 What is the approximate percent composition by mass of CaBr2 (formula mass = 200)
Premium Water Ideal gas law Melting point
TITLE PAGE PREPARATION AND CHARACTERIZATION OF SODIUM SALICYLATE OINTMENT INTENDED FOR TOPICAL AND SYSTEMIC DELIVERY BY MUOBIKE MAKUO 2005/136609 IN PARTIAL FULFILLMENT OF THE REQUIREMENT FOR THE AWARD OF DEGREE OF BACHELOR OF PHARMACY (B. PHARM) OF THE UNIVERSITY OF NIGERIA‚ NSUKKA. DEPARTMENT OF PHARMACEUTICAL TECHNOLOGY FACULTY OF PHARMACEUTICAL SCIENCES UNIVERSITY OF NIGERIA‚ NSUKKA. PROJECT SUPERVISOR: DR. I. V. ONYISHI OCTOBER‚ 2012. APPROVAL PAGE This is to certify
Premium Solubility Melting point PH
used to measure temperature. The extremely fine tube (narrow bore) of a thermometer is called a capillary. The boiling point of water (or condensing point of steam) is 100oC or 212oF or 373 K. The freezing point of water (or melting point of ice) is 0oC or 32oF or 273 K. These temperatures are typically used in the calibration of thermometers and are known as the fixed points. The temperature range that is typically marked on a laboratory thermometer is −10oC to 110oC. Thermometric liquids are
Premium Temperature Liquid Thermodynamics
container’s ice has been half melted. To keep this experiment valid I will keep the amount of ice‚ the time‚ and the amount of materials the same. In my experiment I will test to see what materials will change the ice to its freezing point depression state where it will be melting and there will be ice surrounded by water it just melted off. A few more scientific concepts that relate to this are the Freezing
Premium Water Temperature Chemistry
advantages of the one pierce mold casting include simplicity‚ low cost‚ and no seam lines in finished patterns. As with all manufacturing methods there some disadvantages to casting that include it can only be used with non-ferrous metals that has low melting temperature and long cooling time. As for the material used which consisted of a silicone mold making rubber and a special chemical composition (catalyst) with a usage ratio of 10 to 1. The calculate amount used for the silicone rubber was 918 g
Premium Recycling Melting point Polymer
Acetone has a molar mass of 58.1 g mol-1 and a density of 0.787 g cm-3. Chloroform has a molar mass of 119.4 g mol-1 and a density of 1.499 g cm-3. Estimate the volume of the above mixture using this information. 3. Calculate the molal freezing point depression constant Kf for 1-octadecanol using: Tf = 57.95 oC‚ Hfus = 74.047 kJ mol-1‚ and M = 270.5 g mol-1. ΔTf = Kf m 4. A polymer chemist dissolves 20.00g of polystyrene in 1.000L of benzene. The solution is found to generate an osmotic
Premium Thermodynamics Volume Temperature
find the quality of NaCl as a deicer. These experiments included testing the freezing point depression of NaCl in solution at two different concentrations‚ testing for the H of an aqueous NaCl solution‚ and combining NaCl with MgCl2 in an aqueous solution to test for freezing point depression. Through these various experiments we found NaCl to be the best deicer for our region due to its proficient freezing point depression and its cost efficiency. Introduction As scientists we were given the
Premium Sodium chloride Chemistry Concentration