Determination of g by Free Fall Raw Data: Time (ms) ± 0.01ms Height of release of ball from the sensor plate (cm) ±0.1cm Trial 1 Trial 2 Trial 3 Trial 4 Trial 5 0.0 0.00 0.00 0.00 0.00 0.00 15.0 180.05 179.36 178.74 180.26 180.23 30.0 244.33 244.21 244.71 243.88 245.87 45.0 300.72 301.29 300.59 301.43 301.70 60.0 348.68 348.39 348.77 349.12 348.35 75.0 390.27 390.77 389.58 391.19 390.43 This table below is the results obtained during the experiment in cm/ms. This table below is the results
Premium Measurement Numerical analysis Standard deviation
Density Lab Report PURPOSE: a. To measure the masses and volumes of solids and liquids b. To calculate the densities of solids and liquids c. To calculate the specific gravities of solids and liquids d. To calculate the volume of a rectangular object and to express the volume in volume metric units e. To record data and calculate the values in the correct number of significant figures MATERIALS: 10 mL graduate balance test tube rack unknown liquid 50 mL graduate test
Premium Density Volume
The Density Challenge: A Complete Inquiry Activity Introduction Density has been an important part of science for a very long time. Density was discovered by Archimedes‚ a Greek mathematician‚ around 250 BC while determining whether a craftsman had replaced some of the gold in the King of Syracuse’s crown with silver. Density is the compactness of a substance. The new concept of density he discovered was used to expose the fraud. The purpose of this experiment is to make
Premium Density Volume Water
DENSITY OF LIQUIDS AND SOLIDS by Lab instructor: Due date: Results and discussion: The purpose of the experiment was to determine the densities of the unknown liquid and solid as precisely and accurately as possible in order to identify them. It was carried out first on distilled water in order to rule out systematic errors. A 10 mL beaker was placed on a top pan balance and “tared”. The beaker was then removed and 10 mL of distilled water was pipetted into it before it was placed
Premium Water Chemistry Volume
DENISTY LAB 2/25/13 Chemistry H. Mrs. Halme Objective: Your task is to determine the density of 3 known metals: Zinc‚ Copper‚ and Lead. They are each marked. You must then calculate the density of an unknown metal and determine its identity based on your data from your known samples. Reagents: None Equipment: Lead Copper Zinc Triple Beam Balance Graduated cylinder Unknown metal (Magnesium) Beaker Calculator Procedures Preparation: We observed the given equipment
Free Calculator Mathematics Division
INTRODUCTION 1.1 Background of the Experiment Mass density describes how heavy an object is. Defined by the Greek letter ρ‚ read as rho‚ density is a basic yet important physical property of matter. For a bulk body without accounting its existing pores and voids‚ density is represented by the ratio of its mass and volume. It is given by the equation ρ= massvolume 1. The SI unit of density is kg/m3. However‚ its CGS units‚ g/cm3 or g/ mL‚ are the most commonly used ones in the laboratory. The
Premium Density Water Volume
Density Lab Partners: Betty Alcaraz Date: 9/10/13 Teacher: Wright Class: 7th period Introduction/Purpose: To determine the densities of unknown substances. Pre-Lab: 1. Which is heavier‚ a pound of feathers or a pound of lead? a. A pound of lead. 2. What is the density of a mineral if 427 g of the mineral occupy a volume of 35.0cm3? b. 12.2g/cm3 3. The water level in a graduated cylinder stands at 20.0 mL before and at 26.2 mL after a 16.74 g metal sample
Premium Volume Density Mass
Density (Linearized plot) TA: Blue Rex rex Group Members: Billy and Mandy Tuesday; 1200-1350 Abstract: In this lab the density of hand-made clay balls were calculated to understand how scientists model physical effects and to understand logarithmic plots. The hand-made balls ranged from diameters of 2cm to 6cm and were measured with vernier calipers by each member of the group. A total of 6 independent measures of each diameter were taken to establish uncertainty. The clay balls were then
Premium Volume Density Water
Measurement and Density Your Name: ____________________________________________________________ __ Purpose of this Lab What is the goal of this lab? What question are you trying to answer‚ or what problem are you trying to explain? Hypothesis After reading the lab instructions - but before starting the lab - record your best “educated guess” about each experiment: Experiment 1: Which method of finding the density give you the least percent error and why? Experiment 2: After completing the
Premium Chemistry Experiment Test method
The density of fractions 1‚ 2‚ and 3 are as follows: 1.49‚ 1.325‚ and 1.34 g/mL. These values areincorrect because the density should not have been over 1.0 g/mL. This is because the density of water is 1.0 g/mL‚ and the product should have had a mixture of ethanol and water‚ making the density lower. The measured weight of the vials and ethanol were incorrect due the scales.There are many factors that can cause a scale not to read the correct value. The first is the airflow underneath the weighing
Premium Density Volume Water