Water Wheel Work‚ Power‚ and Efficiency Pre-Lab Preparation: Purpose: The purpose of this lab was to create an efficient water wheel that would produce a productive time in lifting the cup of nuts and bolts that was attached to the pipe used in rotating out water wheel. The more efficient our wheel was the better the time we would have in lifting our cup. We were then able to observe the work that was needed to turn the axel‚ the time that is taken to bring the cup of washers to the axel‚ and
Free Scientific method Hypothesis Observation
Lab Title: "The Effect of Salt on the Boiling Point of Water" Lab Question: How does adding salt to water affects it’s boiling point? Prediction : In this paper‚ a newly proposed model based on solvation between pure solvent and salt for prediction of salt effect on vapor–liquid equilibria is presented by using only the vapor pressure depression data of pure solvent+salt systems that compose the mixed solvent with salt system Materials : 200 mL of distilled water‚ 2 beakers
Premium Water Temperature Thermodynamics
Water Testing Lab Conclusion In this lab‚ chemical tests were used to check for the presence of calcium‚ chloride‚ and sulfate ions in water samples. To do this‚ the testers started with five samples: a reference‚ a sample of only the chemical being tested for‚ a control‚ distilled water‚ two home water samples‚ and a school water sample. To test for the ions in the water‚ a chemical that would react with the ion and create a precipitate was added. If the precipitate was not easily visible‚ a
Free Ion Sodium chloride Sodium
The purpose of this lab was to model the significant differences in density that oceans experience when glaciers and polar ice caps melt. It demonstrated that the variation in density greatly affects salt water. I discovered that the increase in freshwater causes a decrease in density. I made three claims. First‚ the higher the salinity of the water is‚ the denser it will be. This was shown in my data by the fact that‚ with 0mL of fresh water‚ the density was 1.108 g/mL For every milliliter of fresh
Premium Global warming Climate change Water
In conclusion‚ after conducting the lab‚ the emergent properties of water were tested and proved. These trials and experiments were able to verify the adhesion‚ cohesion‚ polarity‚ temperature stabilization‚ solvency‚ and density changes exhibited by water. During the glass and wax paper lab‚ we observed the adhesive properties of water. When a droplet of water touched the glass‚ it dispersed immediately. The droplet placed on the wax paper remained intact and in droplet form. Also‚ when the
Premium Water Atom Oxygen
Title: Determination of Iron in Natural water by Spectrophotometry. Aim: To determine the iron in natural water by spectrophotometry. Abstract: The iron in natural water was determined by utilizing spectrophotometric analysis. That was done by measuring the absorbance of five Fe(oPH)2+3 standards at 510 nm. From that information‚ a calibration curve was plotted and used to find the amount of Fe2+ that was in two unknown water samples based on the absorbance readings obtained with them at 510nm. The
Premium Electromagnetic spectrum Spectroscopy Light
DETERMINATION OF BOILING POINTS Introduction: The boiling point of a compound is the temperature at which it changes from a liquid to a gas. This is a physical property often used to identify substances or to check the purity of the compound. It is difficult‚ though‚ to find a boiling point. Usually‚ chemists can only obtain a boiling range of a 2 - 3oC accuracy. This is usually sufficient for most uses of the boiling point. Purpose: The purpose of this experiment is to determine the
Free Gas Temperature Water
Determination of g by Free Fall Raw Data: Time (ms) ± 0.01ms Height of release of ball from the sensor plate (cm) ±0.1cm Trial 1 Trial 2 Trial 3 Trial 4 Trial 5 0.0 0.00 0.00 0.00 0.00 0.00 15.0 180.05 179.36 178.74 180.26 180.23 30.0 244.33 244.21 244.71 243.88 245.87 45.0 300.72 301.29 300.59 301.43 301.70 60.0 348.68 348.39 348.77 349.12 348.35 75.0 390.27 390.77 389.58 391.19 390.43 This table below is the results obtained during the experiment in cm/ms. This table below is the results
Premium Measurement Numerical analysis Standard deviation
Investigation Followup PROCEDURE The purpose of this experiment is to test different minerals to see where on the Mohs hardness scale they would fit. My question and problem‚ “What mineral is the hardest out of all?” My hypothesis is by looking at all mine minerals‚ amethyst is the hardest mineral‚ followed by opal‚ than apatite‚ then halite‚ than graphite and the muscovite will be the softest mineral. To begin this experiment‚ I purchased and gathered all my materials
Premium Mineral Chemistry Hardness
Jahzeel Morales Jessa Arellano September 19‚ 2014 Period 4 Lab #1: Density Determinations for Solutions Theory: The density of a sample of matter is very useful when trying to find the identity of an unknown substance. The units of density are quoted in (g/mL) for liquid samples of matter. For that reason if the volume is known of a liquid‚ determining its density is easily determined by weighing it accurately. Density can also be used as a tool for finding the concentration of solutions
Premium Solution Concentration Volume