Physics Lab report Aammar Paracha Section MX Feb 6th 2015 OPTICS Abstract: This experiment revolves around using light rays and lenses. The experiment also discusses different properties of light rays. This experiment uses different lenses and measurements to produce images and observes different techniques to obtain the image position. Question and Answers: 1. Use your data to verify the Law of Reflection and then use Snell’s Law to calculate
Premium Optics Lens
(100 ºC) and an acidic pH. Enzyme C produced the most maltose at 37 ºC (body temperature) and a pH of 7 (neutral). Conclusion In a prior lab‚ it was given that the enzyme Aspergillus oryzae (fungus) works best at warm temperatures and an acidic pH‚ porcine (pig) works best at body temperature (37 ºC) and
Premium Enzyme Chemical reaction Metabolism
1. Introduction Microscopy is an essential technique not only in cell biology but natural science as a whole. We compared different types of microscopic techniques ‚ according to the specimen used and the scope of the experiment. Two specimens‚ stained and unstained‚ containing CHO cells‚ were prepared‚ examined and analyzed under the microscope using bright field (HF)‚ dark field (DF) and phase contrast (PH) settings. In addition‚ the four phases of cell division cycle were estimated.. Bright
Premium Cell Cell nucleus Mitosis
Raquel Johnson October 19‚ 2014 Solids: Recrystallization and Melting Points Organic Chemistry 2423 Lab Report: Recrystallization Abstract: The purpose of this lab was to purify an unknown compound by recrystallization. Taking an unknown compound and identifying it by purifying it from its impurities through the use of hot gravity filtration. Then to determine the unknown you were to take the melting point. An unknown compound was recrystallized from hot water to produce 0.99 grams (67% recovery)
Premium Temperature Solubility Solid
DNA Extraction Lab 1/17/14 Purpose : This lab was conducted in order to show and analyze the way DNA is extracted. Hypothesis: If the lab is conducted properly then we should be able to view a visible amount of DNA from the strawberry and detergent mixture. Variables: The independent variable in this experiment is the strawberry mixture while the dependent
Premium DNA
Introduction and Purpose: This lab focuses on how weight affects the time it takes for a rotocopter to fall from a drop height of 1 and 2 meter(s) respectively. The primary goal of this lab is to investigate and explain the relationship of these two factors. During the process of conducting this experiment‚ learning to design a lab will also be achieved. Research Question: What is the effect of weight on the time it takes for a rotocopter to fall from a drop height of 1 and 2 meter(s)? Variable
Premium Force Classical mechanics Mass
Impurity Lab Report Aim: To find out the difference of the boiling point and melting point when adding impurity (salt) to water. Diagram: Method: 1.Set up the apparatus as shown in the diagram 2. Get a known amount of ice in the beaker (half full)‚ and a known amount of salt in another beaker 3. Measure the temperature (melting point) of the ice without adding any impurity (salt). 4. Measure the temperature (melting point) of the ice after adding the salt into the beaker. 5. Heat up
Premium Water Solid Fahrenheit
Lab Report Procedure 6.1: Perform Benedict’s test for reducing sugars. Introduction: Benedict’s tests allows for the detection of the presence of reducing sugars. All monosaccharides are reducing sugars since all of them have active carbonyl group. Some disaccharides that are exposed to a carbonyl group are also reducing sugars but less reactive than monosaccharides. By mixing the sugar solution with Benedict’s solution and heating them‚ a redox reaction will occur. The copper (II) sulphate
Free Glucose Carbohydrate Sucrose
Lab Report Density Name: Period: Problem How do you calculate Density? What units did you use for volume‚ mass‚ and density? When the cubes are placed in water which one will sink 1st? What is the ranking of the cubes lightest (1) to heaviest (10)? Is it true that the cube with the most mass will have the most density? Hypothesis I think the 1st cube was aluminum I think the 2nd cube was steel I think the 3rd cube was brass I think the 4th cube was copper I think the 5th
Premium Density Volume
ABSTRACT On the past two weeks‚ I have done an experiment on hydrostatics‚ or is also known as fluid statics (fluid at rest) within the fluid mechanics field of study. This condition explains that in a stable condition‚ the fluid is at rest. The use of fluid in doing work is known as hydraulics‚ and the science of fluid in motion is known as fluid dynamics. INTRODUCTION The natural nature of fluids are they cannot remain stationary under the application of shear stress. However‚ fluid
Premium Fluid mechanics Force Fluid dynamics