Institute Physics Course 2014 - Rocket Lab Report Title: RockSim and Electronic Altimeter Measurement Techniques Name: Scarlet Henriquez Email: scarletpatricia94@aol.com LAB SESSION ___8____Assignment _____7_____ Due Date: ___7/8/14______ Objective: Launch a smaller rocket to learn how to compare RockSim predictions (computer based) to an actual instrument measurement carried by the rocket (Electronic Altimeter). This Lab shows how better the electronic measurement
Premium Rocket Mathematics Flight
Lab Report 3 In this lab‚ we will take a trip to the planetarium lab and will learn about Right ascension and declination‚ and altitude and zenith. After looking at the different points shown‚ we will log the altitude and zenith in the chart in our lab manual. Now we will look at the same points and label the right ascension and declination. Then we will learn about the easiest way to locate the star Polaris. As we started the first program‚ we answered a few questions to make sure we knew
Premium
This lab report will be detailing the steps taken and the results discovered when using spectrophotometry to determine the percentage of copper in a copper-clad penny and the thicknes of the copper layer on the copper-clad penny. After 1982‚ copper coating has been used in the creation of the penny because the cost of pure copper has increase to the point that the amount needed t omake a penny cost far more than the actual value of the penny. This lab allowed us to see just how much copper coating
Premium Chemistry Spectroscopy Ammonia
INTRODUCTION The measurement of fluid flow is very important in our daily life from measurements of blood-flow rates in human artery to the measurement of liquid oxygen in a rocket. In this experiment‚ students are to adapt to various ways to measure the flow of essentially incompressible fluids by using the flow measuring apparatus. Students will also be able to understand the application of Bernoulli’s equation in this experiment. The flow is measured by using a venture meter‚ an orifice meter
Premium Fluid dynamics Mass flow rate
MEC 325/580 Lab Report CNC Machining Lab Report Date: March 18‚ 2013 Group Leader: Jian Wu Team Members: Group Number: G4 Regment No.: D Insturctor: CONTENTS 1.Objective and introduction. 2.Principles and practice. 3.Design and result. 4.Conclusion and recommendations. Appendices 1. Objective and introduction * Objectives Operate the CNC milling machine using G-codes‚ M-codes in a CNC program. * Equipment: Minitech CNC machine (Series 2) * Machine
Premium Milling machine Numerical control
Lab #4: The Immune System Purpose: The purpose of this lab was to perform and understand the procedures of conducting an ELISA test to determine whether a particular antibody is present in a patient’s blood sample through a virtual simulation. Hypothesis: If I successfully complete this lab‚ I will then understand how to perform an ELISA test‚ the purpose an ELISA test‚ and also how to interpret the results of this test. Materials and Procedures: Materials: Howard Huges medical
Premium Antibody Immune system Immunology
Growth Dynamics of E. coli in Varying Concentrations of Nutrient Broths‚ pH‚ and in the Presence of an Antibiotic Dvora Szego‚ Elysia Preston Darcy Kmiotek‚ Brian Libby Department of Biology Rensselaer Polytechnic Institute Troy‚ NY 12180 Abstract The purpose in this experiment of growth dynamics of E. coli in varying media was to determine which media produces the maximum number of cells per unit time. First a control was established for E. coli in a 1.0x nutrient broth. This was used to compare
Premium Bacteria PH Protein
2. To determine the conditions under which types of flow occur. 3. To compute Reynolds Number (Re) on fluid flow conditions. EQUIPMENTS AND APPARATUS a) Dye reservoir. b) Stilling tank. c) Observation tube. d) Stopwatch e) Graduated cylinder THEORY Reynolds number is used to distinguish between laminar‚ transitional and turbulent flows. Re = Reynolds number V = Fluid velocity (m/s) d = Pipe diameter (0.012m) v = Kinematic viscosity (0.893 x 10-6m2/s) Laminar
Premium Fluid dynamics Fluid mechanics Viscosity
Lab Report Abstract: The purpose of this lab was to see how magnesium reacts with oxygen. This reaction must be forced with heat. As magnesium changes to magnesium oxide the mass increased. Procedure: 1. Set up the stand and bunsen burne. 2. Go to crucible heat oven to obtain a crucible. 3. Weigh the crucible and lids mass. 4. Break up the magnesium ribbon on the crucible and weigh the mass of the magnesium‚ crucible‚ and lid. 5. Place the crucible on the ring stand over the flame. Allow
Free Force Mass Oxide
Lab Report Janice Chisholm SCI207: Dependence of Man on the Environment Instructor: Lee Ott April 28‚ 2013 1. What patterns do you observe on the information table 4? While observing the information in table 4‚ it appears that the number of fish changes from time to time and the oxygen increases and / or decreases when this occurs. 2. Develop a hypothesis relating to the amount of dissolved oxygen measured in the water sample and the number of fish observed in the body of water?
Free Observation Scientific method Hypothesis