Safety Concerns in the Laboratory Safety goggles must be warn at all times during a lab session. This is very important because they protect your eyes from harmful matter such as chemicals‚ glass‚ and fumes. It is very important to note that they must be goggles and not glasses. Safety glasses may protect the eyes from flying debris and splashes but may not protect the eyes from gas fumes or splashes from underneath. Also‚ wearing contact lenses in a chemical laboratory without proper coverage
Premium Chemistry Laboratory Left-wing politics
BIOMAGNIFICATION LAB REPORT AIM The aim of this lab is to model bioaccumulation and biomagnification through a food chain. MATERIALS 100 M&M’s Paper towel to lay M&M’s on 20 small cups labelled “zooplankton” 5 medium cups labelled “minnow” 2 larger cups - one labelled “eel #1”‚ and another labelled “eel #2” 1 bowl labelled “osprey” PROCEDURE The pile of M&M’s represents the phytoplankton population in a lake. The printed “M” on the candy represents the amount of DDT (in ppm)
Premium DNA Protein Gene
Utilizing the Lab Results PS2200 - Criminal Investigation Unit 04 Assignment 01 As the lead homicide investigator for this case I had recently learned that the crime lab has concluded that the finger print that was recovered belonged to the boyfriend‚ they were from a piece of notebook paper found under the body of the victim. Interviews are conducted in criminal cases for the purpose of gathering information from people who have‚ or may have‚ knowledge needed in the investigation. (Swanson
Premium Criminal law Arrest warrant Scientific method
The lab in which we conducted last Tuesday was an analysis of a hydrate and what happens to it when it is heated. A hydrate is a crystalline compound which water molecules are chemically bound to it. In the lab‚ we were to analyze the difference in grams of the hydrate and the anhydrate. An anhydrate is the crystalline compound without the water molecules bound to it. During our lab‚ we were to heat up the crucible‚ the crucible with hydrate‚ and the crucible with an anhydrous and write down each
Premium Water Laboratory equipment
Introduction The purpose of this lab is to determine the percent mass of Cu in a penny and see if the fabricator that makes the planchets for the government is using the correct amounts of Cu in the pennies. The composition of a standard penny is 97.5% Zn and 2.5% Cu. In the lab we will be using Beer’s Law (A=elc+b where A is solution absorbance‚ e is a constant called molar absorbency‚ l is the length in cm‚ and c is the concentration). Using Beer’s Law in this lab a colorimeter is used to find the
Premium Chemistry Chemical element Copper
Lab report is one way we used during of after an experiment in a laboratory to subtly record and discuss the experiment. During a lab‚ we sometimes can observe only the physical part of the experiment‚ or may be some visible chemical changes. These changes indicate that the experiment we do is successful or not. However‚ in order to understand and achieve more from just simply doing the experiment‚ we write lab report to more profoundly understand the internal meanings of the experiment we do‚ and
Premium Critical thinking Thought
original state and the percent of the hydrate recovered was calculated by using the mass of the rehydrated sample by the mass of the original hydrate and then multiplied by 100%. Data Presentation & Analysis Table 1: The data was collected from the lab experiment. Sample calculations are shown. Mass of beaker with sample 30.765g Mass of empty beaker 30.263g Mass of sample .502g Mass of beaker with sample after 1st heat 30.661g Mass of beaker with sample after 2nd heat 30.657g Heating mass
Premium Mathematics Mole Heat
Density Lab Partners: Betty Alcaraz Date: 9/10/13 Teacher: Wright Class: 7th period Introduction/Purpose: To determine the densities of unknown substances. Pre-Lab: 1. Which is heavier‚ a pound of feathers or a pound of lead? a. A pound of lead. 2. What is the density of a mineral if 427 g of the mineral occupy a volume of 35.0cm3? b. 12.2g/cm3 3. The water level in a graduated cylinder stands at 20.0 mL before and at 26.2 mL after a 16.74 g metal sample
Premium Volume Density Mass
Collision Lab Simulation Purpose: To study elastic and inelastic collisions in one-dimension. Background Information: Momentum: is a measure of mass in motion. It is the product of mass x velocity. Conservation of Momentum: in the absence of external forces‚ such as friction‚ the linear momentum of a system remains constant. Procedure: 1. Open web browser and go to the site: http://phet.colorado.edu 2. Click “play with sims”‚ then “physics”‚ and then “motion” 3. Find the “Collision Lab” 4
Premium Classical mechanics Inelastic collision Kinetic energy
Jeanine Campa Biology 101 10/20/2010 Ecology-Interspecific Interactions Lab Intro: Ecology is the study of how organisms interact within their environment. Every species interacts with its surroundings‚ whether it’s within their populations‚ community‚ ecosystem‚ etc. In this lab‚ we will be comparing two different species and how they grow alone as well as together‚ in the same environment. More specifically‚ in this lab‚ we will be dealing with one of the most important ideas in ecology‚ the
Premium Species Ecology Competition