"Effect of temperature on the rate of osmosis lab report" Essays and Research Papers

Sort By:
Satisfactory Essays
Good Essays
Better Essays
Powerful Essays
Best Essays
Page 32 of 50 - About 500 Essays
  • Good Essays

    The effect of temperature on the cell membranes of beetroot cells and amount of pigment released. Apparatus • Corer size 4 • White tile • A Beetroot • Automatic Water Bath • Segregated knife • A thermometer • Stopwatch Method: • First take the white tile and the corer. Then collect a cylinder of beetroot by pushing the corer into the beetroot and withdrawing it. The cylinder remains inside the corer- so push it out with the end of a pencil. • Collect 3 cylinders

    Premium Cell membrane Protein Cell

    • 1207 Words
    • 5 Pages
    Good Essays
  • Satisfactory Essays

    Exploring Rates‚ Equilibrium‚ and Organic Chemistry Brandon Sher SCH 4U For: Ms. Merhai Due date: June 1st‚2013 Introduction: Organic chemistry. Two quantities one could measure with the presence of organic chemicals are chemical equilibrium and rate of reaction. Chemical equilibrium is the ratio between the forward and reverse process of a reaction. This is represented by the equation: K = products / reactants. When a reaction has reached equilibrium‚ the

    Premium Chemical reaction Chemistry Erlenmeyer flask

    • 758 Words
    • 4 Pages
    Satisfactory Essays
  • Better Essays

    Effect of Varying Temperatures: The enzyme catalyzed reaction rate during varying incubation temperatures are plotted on Figure. 6. As the temperature increases the rate increases‚ but as the temperature reaches 49oC it begins to drop. When the plot of the logarithm of the rate is used against the inverse of the temperature kelvin’s the Arrhenius equation is used to calculate the activation energy. The range in orange is between 16.5 - 37oC and the activation energy is calculated to be 9332kcal/mol

    Premium Chemical reaction Enzyme Temperature

    • 1679 Words
    • 7 Pages
    Better Essays
  • Satisfactory Essays

    Lab Report

    • 527 Words
    • 3 Pages

    John Angelo F. Raule Marvin Reyes Mykee Domingo Aaron Santos Ralph Reyes LBYMATB V26B Report Title Of Activity: Yogurt Making Date Performed: October 4‚ 2012 I. Introduction Last October 4‚ the group performed an activity that involved making our own yogurt. The group prepared the materials and followed the procedures to make the said yogurt. In the activity paper that was given‚ it dictated that during the yogurt making process‚ the bacteria underwent fermentation. “Fermentation

    Premium Milk

    • 527 Words
    • 3 Pages
    Satisfactory Essays
  • Powerful Essays

    “The Domino Effect” Teacher’s Prompt Investigate the domino effect with a set of dominoes. Aim To investigate the relationship between the mass of the dominoes‚ and how it impacts the time taken of the domino effect. Independent Variable: The mass of each domino (12.38 g‚ 32.38 g‚ 42.38 g‚ 62.38 g‚ 82.38 g). Dependent Variable: Time taken of the domino effect. Controlled Variable: The number of dominoes used (8 dominoes)‚ the distance between the dominoes (2 cm)‚ the loads used as the initial

    Premium Causality Mass Force

    • 1145 Words
    • 4 Pages
    Powerful Essays
  • Powerful Essays

    Osmosis investigation Aim: To investigate how sugar concentration affects the mass or size of a potato and find out the sugar solution. Introduction: Osmosis is the movement of water molecules across a partially permeable membrane form a region of high water concentration to a region of low water concentration until the concentration on both sides is equal. This means that osmosis is like diffusion involving water molecules. Osmosis occurs across a partially permeable membrane‚ with holes

    Premium Osmosis Chemistry Concentration

    • 2262 Words
    • 10 Pages
    Powerful Essays
  • Satisfactory Essays

    Lab Report

    • 511 Words
    • 3 Pages

    This lab report will be detailing the steps taken and the results discovered when using spectrophotometry to determine the percentage of copper in a copper-clad penny and the thicknes of the copper layer on the copper-clad penny. After 1982‚ copper coating has been used in the creation of the penny because the cost of pure copper has increase to the point that the amount needed t omake a penny cost far more than the actual value of the penny. This lab allowed us to see just how much copper coating

    Premium Chemistry Spectroscopy Ammonia

    • 511 Words
    • 3 Pages
    Satisfactory Essays
  • Powerful Essays

    Lab report

    • 1662 Words
    • 6 Pages

    LSM1102 Lab Report Introduction Transformation is a process which involves plasmid DNA being bound to the cell surface and the subsequent uptake of DNA by the cell (Panja et al.‚ 2008). For artificial transformation of E. coli cells with plasmids‚ plasmid DNA has to be extracted from bacterial cells using the High-Speed Plasmid Mini Kit‚ which is then mixed with competent E. coli cells followed by heat shock and the streaking of transformed cells on two different types of agar plate (LB and LB+ampicillin)

    Premium Plasmid Transformation Escherichia coli

    • 1662 Words
    • 6 Pages
    Powerful Essays
  • Good Essays

    be seen in the graph‚ the higher the temperature the shorter the time is for the Sulphur to be created. If it is looked as one continuous line‚ the first part of the trend line shows a steep‚ straight and constant decrease; then the 2nd part is not as steep and has a more gradual decline. Moreover‚ it shows how a reaction at 20°C a slower time for the cross to disappear compared to 40°C and especially 60°C. Both graphs show how temperature has a great effect on the speed of sulfur formation covering

    Premium Temperature Chemical reaction Thermodynamics

    • 896 Words
    • 4 Pages
    Good Essays
  • Powerful Essays

    Lab Report

    • 1099 Words
    • 5 Pages

    MEC 325/580 Lab Report CNC Machining Lab Report Date: March 18‚ 2013 Group Leader: Jian Wu Team Members: Group Number: G4 Regment No.: D Insturctor: CONTENTS 1.Objective and introduction. 2.Principles and practice. 3.Design and result. 4.Conclusion and recommendations. Appendices 1. Objective and introduction * Objectives Operate the CNC milling machine using G-codes‚ M-codes in a CNC program. * Equipment: Minitech CNC machine (Series 2) * Machine

    Premium Milling machine Numerical control

    • 1099 Words
    • 5 Pages
    Powerful Essays
Page 1 29 30 31 32 33 34 35 36 50