CHM130 Lab 5 The Atomic Mass of Beanium Name: Paige Miller A. Data Table: Insert your Data Table here with your sample calculations. You must show at least one sample calculation per procedure step. (16 points) Part I Data Table Sample Mass (mg) Number/Qty Average Mass (mg) Relative Abundance Relative Weight (mg) Kidneybeanium 1660.00 mg 3 553.33 mg 0.2143 118.58 mg Pintobeanium 2830.00 mg 6 471.67 mg 0.4286 202.16 mg Blackeyedpeaium 1110.00 mg 5 222.00 mg
Premium Atom Chlorine Atomic number
root tip of a plant spend a comparatively long time in the mitotic phase‚ whereas those cells comprising slow-growing tissues would spend most of their lives in interphase. Non-dividing cells remain in interphase and never enter the mitotic phase. (Lab Manual 64) Interphase is the synthesis of biological molecules including DNA and duplicated DNA with associated proteins. These comprise the chromatin that begin to condense toward the end of this phase‚ but are not yet visible. The nucleoplasm
Premium Mitosis Cell cycle Cell nucleus
Equipment: 0.00200 M KNCS‚ 0.00200 M Fe(NO3)3 0.200 M Fe(NO3)3‚ 0.10 M HNO3‚ 5 Cuvettes‚ 1 colorimeter 4 100ml beakers‚ 5 Test tubes 2 250ml Graduated cylinder. The first step is to calibrate the colorimeter with0.20 M Fe(NO3)3and set the absorbance at 470 nm since it is known to keep an acidic solution throughout the entirety of the experiment. It was important to do this right at the beginning of the lab since the zeroed value of the acid was the calibration number for all of the other solutions
Premium Metrology Laboratory glassware Volume
OF EXPERIMENT The purpose of this lab was to determine the magnitude of the uncertainties produced when making measurements using common lab equipment. II.APPARATUS AND MATERIALS NEEDED safety goggles distilled water (at 20°C) laboratory apron dropper laboratory balance 2 objects of unknown mass standard masses graduated cylinder‚ 10-mL graduated cylinder‚ 100-mL III.PROCEDURE Part A: Estimating the Uncertainty of a Balance 1.We put on lab aprons and goggles. Then‚ we used the
Premium Mass Measurement Uncertainty
! Name: Laura Romero ! 5.04H: Gas Stoichiometry Lab Worksheet Data and Observations: Present all relevant data in a data table below. Include an observations section for any observations that you made during the lab. (5 points) Data Table Mass of magnesium strip (grams) 0.032 g Volume of gas collected (mL) 30mL Barometric pressure (atm) 1.1 atm Room Temperature (°C) 22 °C Vapor pressure of the water (torr) 19.8 torr ! ! Calculations: ! 1. Write the
Premium Pressure Stoichiometry
Title: Calculating the Atomic Mass of “Pennium” Purpose: The purpose of this lab is to calculate the atomic mass of “pennium” using pennies made before 1982 and pennies made 1982 or after. Hypothesis: The atomic mass of the pennium will be the average of the average masses of a pre-1982 penny and a post 1982 penny. Procedure: 1. Obtain a bag of pennies 2. Determine the total number of pennies in the bag. Record the value. 3. Sort the pennies by date into 2 piles. One pile should consist
Premium Atom Isotope Copper
BIOS251 Week 4 Lab Anatomy of the Skeletal System Exercise – Answer Key 1. What area of the long bone is covered with cartilage? (3 points) 2. What type of cartilage is articular cartilage? (3 points) 3. What area the epiphysis or diaphysis is made up of a thin layer of compact bone and a very thick layer of spongy bone? (3 points) 4. What area the epiphysis or diaphysis is made up of a thick layer of compact bone and a very thin layer of spongy bone.(3 points) 5. Identify the
Premium Bone
Lab Report Experiment 1 & 2 CHM-101 Amele Takpara Partner: Jessamyn Dupree ------------------------------------------------- Experiment 1 ------------------------------------------------- (Pre-Lab Questions) 1. In the design of a Bunsen burner‚ explain the purpose of a. the gas control valve The gas control valve regulates the rate at which methane enters the burner. b. and the air vents. The air vents control the rate at which air enters the burner 2. Why is a luminous
Premium Temperature Volume Liquid
BioLab3 Lab Report 5 Enzymes Student Name: Cooper Lyon I. Enzyme Structure and Function EXERCISE 1 – Preparation of an enzyme activity standard At five minute intervals over the next fifteen minute period‚ record the color intensity of the solution of each test tube. Time (min) Tube S1 Potato Extract + Catechol Tube S2 Potato Extract + Water Tube S3 Catechol + Water 0 Shade of Yellow Clear/Milky Clear/Milky 5 Shade of Yellow Clear/Milky Clear/Milky 10 Orange Clear/Milky Clear/Milky 15
Premium Enzyme PH
Molar Mass Lab 3.09 Molar Mass of Compounds Purpose: The purpose of this experiment is to determine the formula of a copper sulfate hydrate by heating it up. Materials: Hydrate‚ crucible‚ balance‚ Bunsen burner and scale Procedure: First you measure the mass of the empty crucible and record that mass. Then you should fill the crucible with 3-5 scoops of the hydrate and record that mass as well. Heat the hydrate filled crucible above the Bunsen burner for 10 minutes for all f the water to evaporate
Premium Water Mass Addition