a Cisccustomer router? (Choose two.) The PPP configuration is on the dialer interface. An MTU size of 1492 bytes is configured on the Ethernet interface. The Ethernet interface does not have an IP address. The customer router CHAP username and password are independent of what is configured on the ISP router. The dialer pool command is applied tthe Ethernet interface tlink it tthe dialer interface. 6. Fill in the blank. DOCSIS specifies the ”MAC“ sub-layer as a Layer 2 requirement that defines
Premium OSI model Ethernet Virtual private network
reach the destination network. Each network that a router connects to typically requires a separate interface. These interfaces are used to connect a combination of both Local Area Networks (LANs) and Wide Area Networks (WANs). LANs are commonly Ethernet networks that contain devices such as PCs‚ printers‚ and servers. WANs are used to connect networks over a large geographical area. For example‚ a WAN connection is commonly used to connect a LAN to the Internet Service Provider (ISP) network.
Premium Computer network Routing Ethernet
Explaining the Differences Including Advantages and Disadvantages NTC/360 By Betsy Grissom Earl Sortor November 15‚ 2010 Introduction After reading this paper the reader should know how each of the terms works in a computer. The reader will also have knowledge of each terms advantages and disadvantages. Mesh Topology A mesh network has a very simple concept. Because of the simple concept a mesh network has fewer chances of breaking down the network. Many possible combinations
Premium Network topology Ethernet OSI model
TYPES OF NETWORKING A computer network is a telecommunications network that allows computers to exchange data. The physical connection between networked computing devices is established using either cable media or wireless media. The best-known computer network is the Internet. Network devices that originate‚ route and terminate the data are called network nodes.[1] Nodes can include hosts such as servers and personal computers‚ as well as networking hardware. Two devices are said to be networked
Premium Ethernet Computer network
OVERVIEW OF BROAD BAND Definition of Broad Band Broadband is often called high-speed Internet‚ because it usually has a high rate of data transmission. In general‚ any connection to the customer of 256 kbit/s or more is considered broadband. HOW IS BROADBAND DIFFERENT FROM DIAL-UP SERVICE? Broadband service provides higher speed of data transmission—Allows more content to be carried through the transmission “pipeline.” Broadband provides access to the highest quality Internet services—streaming
Premium Broadband Internet access Broadband Internet
UNIVERSITY OF OSLO Department of Informatics in collaboration with OSLO UNIVERSITY COLLEGE Department of Computer Science MASTER THESIS ADMINISTRATION OF REMOTE COMPUTER NETWORKS Stig Jarle Fjeldbo May 23‚ 2005 Abstract Today’s computer networks have gone from typically being a small local area network‚ to wide area networks‚ where users and servers are interconnected with each other from all over the world. This development has gradually expanded as bandwidth has become
Premium Computer network Ethernet Network topology
: The typical definition of Local Area Network (LAN) is "two or more connected stations (PCs‚ servers‚ computer…) in the same limited area‚ sharing data and peripheral devices‚ and operating .The most popular LANs include 10 Mbps & 100 Mbps Ethernet‚ 4 Mbps & 16 Mbps Token Ring. HARDWARE COMPONENTS OF LAN NETWORK The hardware components of a LAN consist of: * PCs/workstations and servers * Network Interface Card (NIC) * Cabling and connectors‚ * Hub‚ concentrator‚ and more complicated
Premium Network topology Ethernet Computer network
1) Baseband transmission dominates in LANs because it is ________ than broadband transmission. A) faster B) less expensive C) Both A and B D) Neither A nor B Answer: B 2) Using link aggregation with two or three trunk lines ________ going to a single faster Ethernet port. A) is less expensive than B) is just as fast as C) Both A and B D) Neither A nor B Answer: A 3) The 802.3 100BASETX standard is defined at the ________ layer. A) physical B) data link C) Both A and B D) Neither A nor B Answer: A
Premium Computer network Local area network Ethernet
1. Straight-through cable (39-40): connects the wire at pin 1 on one end of the cable to pin 1 at the other end of the cable; the wire at pin 2 needs to connect to pin 2 on the other end of the cable; pin 3 on one end connects to pin 3 on the other; and so on. (To create a straight-through cable‚ both ends of the cable use the same TIA pinout standard on each end of the cable.) Crossover cable: a cable that swaps the wire pairs inside the cable 2. Collision domain (43): the set of devices whose
Premium IP address Ethernet Subnetwork
cable that connects all nodes on a network without intervening connectivity devices. b. A(n) __serial__ backbone is the simplest kind of backbone. c. Fast Ethernet operates at ___100Mbps___. d. _Switches___ is a component of a network’s logical topology that determines how connections are created between nodes. e. One thing all Ethernet networks have in common is their access method‚ known as ____CSMA/CD___. 2. For the client situation described in the Discussion/Project Topic above‚ use
Premium Computer network Ethernet Network topology