Flame Tests 12.01.2010 19.01.2010 Introduction The normal electron configuration of atoms or ions of an element is known as the “ground state”. In this most stable energy state‚ all electrons are in the lowest energy levels available. When atoms or ions in the ground state are heated to high temperatures‚ some electrons may absorb enough energy to allow them to “jump” to higher energy levels. The element is then said to be in the “excited state”. This excited configuration is unstable‚
Premium Potassium Atom Photon
C. Revising Sentences by Correcting Unclear You didn’t do anything! Comparisons and Incorrect‚ Misplaced‚ and Dangling Modifiers Each of the following sentences contains an unclear comparison‚ an incorrect form of a modifier‚ a misplaced modifier‚ or a dangling modifier. Write each sentence‚ correcting the error. X 21. Seeing that no damage had been done‚ their cars drove away in opposite directions. Seeing that no damage had been done‚ they drove their cars away in opposite directions
Premium
INTRODUCTION Flame photometry‚ also referred to as ’flame atomic emission spectrometry ’ is a quick‚ economical and simple way of detecting traces of metal ions‚ primarily Sodium‚ Potassium‚ Lithium‚ Calcium‚ and Barium‚ in a concentrated solution. The process is an extension of the principles used in a flame test‚ with the main differences having more precision in the results‚ and the use of more advanced technology. This report focuses on the theory‚ applications‚ limitations and analysis of Flame Photometry
Premium Spectroscopy Atom Photon
Title: Flame Test Aim: To determine the cation in each of the unknown substance X‚ Y and Z by observing the flame colour of different metal compounds. Introduction: A distinctive feature of many s-block metals is their ability to produce flame colours. At temperature of a Bunsen flame‚ a compound will decompose to give gaseous atoms of its constituent elements. When an electron in the gaseous atom absorbs energy from the flame‚ it will move from an orbital with lower energy to
Premium Sodium chloride Flame test Potassium
Flame Test Laboratory Report Introduction The purpose of this lab is to observe and identify metallic ions‚ using flame tests. The traditional flame test originated when Robert Bunsen invented the Bunsen burner to test two new alkali metals he and his partner had discovered. “A flame test is an analytic procedure used in chemistry to detect the presence of certain elements‚ primarily metal ions‚ based on each element’s characteristic emission spectrum” (Flame Test 1). Using this test‚ an element
Premium Photon Atom Spectroscopy
INFRA-RED FLAME DETECTION 123 S200+ SERIES TRIPLE IR FLAME DETECTORS USER MANUAL S200+ USER MANUAL INDEX PAGE A) INTRODUCTION 1 1. 1 Flame Detection Operation 1 3. B) Introduction 2. General Construction 4 PRODUCT APPLICATION 5 1. C) Application 5 2. Benefits of the S200+ Series 6 8 Introduction 8 2. Electrical Characteristics 8 3. Mechanical Characteristics 13 4. Environmental
Premium
Flame lab test Chemistry Introduction The lab test performed was to determine characteristic colors that were produced by specific metallic ions that are shown in a flame. This happens when an electron gains energy; the electron moves from an energy level that’s farthest away and to an empty orbital close to the nucleus with higher levels‚ so one of the electrons gives off energy. A flame test is a visual test where the energy is in the form of a color change and the change can
Premium Atom Metal Potassium
Flame Test Lab Question: When a compound is placed in the flame of a burner‚ what happens to the color of the flame? Hypothesis: When the compound is placed in the flame‚ the flame changes color depending on the chemical compound. When they’re heated‚ they gain energy and changed color sometimes. Safety Requirements for this Lab: Wear goggles at all times. If you want to remove them to write in your notebook you may sit at a table in the center of the room. When you sit down remove them
Premium Chemical element Metal Chemical compound
A generation of Suffolk Sporting talent inspired by Olympic flame The Suffolk Youth Games completed its inspirational journey from the millennium to the Olympics yesterday and bowed out in a blaze of glory as the Olympic Torch visited the closing ceremony. Around 800 young people representing Suffolk’s sporting future converged on Bury St Edmunds on Saturday 7th July for the thirteenth staging of the Redrow Homes Suffolk Youth Games. The event‚ organised by Suffolk Sport‚ the County Sports Partnership
Premium Olympic Games 2012 Summer Olympics Summer Olympic Games
Date: 20/03/13 Flame Test – Investigating Compounds Aims To identify the presence of a relatively small amount (ie low concentration) of a metal ion in a compound. Method 1. Clean a platinum or nichrome wire by dipping it into concentrated hydrochloric acid. 2. Hold the platinum or nichrome wire at the hottest or blue part of a non-luminous Bunsen flame. 3. Repeat until the wire does not produce any colour in the flame (note: do not touch the wire‚ as salt in sweat will produce
Premium Metal Ion Ionic bond