Bubble Inside a Bubble Materials • • • • • • • • Granulated sugar (we had our best results using Imperial Sugar and Dixie Crystals) Dish soap Water Tablespoon Scissors Pipette Cup Adult supervision Bubbles form because of a combination of water’s hydrogen bonds and the oily film you can see shimmer in the light. The oily film you see is actually two separate layers of soap attached to‚ and surrounding‚ hydrogen-bonded water. Solar Oven S’mores Materials • Pizza box • Two clear sheet protectors
Premium Oxygen Thermodynamics Water
Coulomb’s Law Purpose: The purpose of this lab was to demonstrate that the force between two stationary charges is directly proportional to the product of the charges and inversely to the square of the distance between them. Coulomb’s law tells us that the force between two charges depends (1) linearly on the strength of each charge‚ and (2) inversely on the square of the distance between them. Mathematically we would write this as . Procedures Part1 Begin by removing the right side
Premium Electric charge
the period of oscillations to the length of the pendulum.Sources of error for this procedure included precision in both length and time measurement tools‚ reaction time of the stopwatch holder‚ and the accuracy of the stopwatch with respect to the lab atomic clock. The final result of g takes into account the correction for the error introduced using the approximation. There are opportunities to correct for the effects of mass distribution‚ air buoyancy and damping‚ and string stretching[1]. Our results
Premium Regression analysis Measurement Normal distribution
CE121: Construction Materials Laboratory Report No. 1 Particle Size Distribution Van Joseph E. Casalme 2010-14928‚ BS Civil Engineering Institute of Civil Engineering‚ College of Engineering University of the Philippines Diliman‚ Diliman Quezon City 1101 Submitted to: Engr. Christian R. Orozco ABSTRACT This test (ASTM C136-06) determines the grading of materials being used as aggregates using two parameters (coefficient of uniformity and gradation) from particle-size distribution
Premium Sieve analysis Particle size distribution Construction aggregate
The purpose of this experiment was to acquaint the students with basic laboratory procedures‚ methods‚ and techniques; to introduce the use of basic laboratory measuring devices; to demonstrate different methods of manipulation of numerical quantities. DENSITY AND SPECIFIC GRAVITY Materials and Methods Part 1: Density of an Unknown Solid 1. We first were asked from our laboratory instructor to attain an unknown solid and were asked to note down the number of the solid. 2. Determine
Premium Density Volume
is the capacitative reactance‚ R is the resistance‚ and ω = 2π f ( f is the linear frequency). Apparatus • PC with DataStudio installed • Science Workshop 750 USB Interface Box • Power Amplifier • Voltage Sensor • AC/DC Electronics Lab Board • LCR meter • Connecting patch cords Experimental Procedure The experimental procedure can be divided into three parts: Part I: Using a Frequency Scan to Determine the Resonance Frequency • The first
Premium Alternating current Inductor Electrical resistance
will leave her. Mei Ling had seen her general practitioner (GP) for lack of energy and vague gastrointestinal symptoms. But her medical examination result found no physical cause. Through discussion with the GP discovered she has been feelings of depression for the past four months. Mei Ling’s GP suggested her to seek counselling. During the counselling session‚ Mei Ling told the counselor she has been feeling “down” and “depressed” most of the time. She burst into tears frequently without knowing
Premium Psychotherapy Therapy Rational emotive behavior therapy
Example lab report of Synthesis of potassium tris (oxalato) ferrate (III) trihydrate Posted by Nurul Yunaliyana Experiment 5: Synthesis of potassium tris (oxalato) ferrate (III) trihydrate Purpose: to synthesis potassium tris (oxalato) ferrate (III) trihydrate ‚K3 [Fe (C2O4)3].3H2O. Introduction: Ferrous ammonium sulfate‚ Fe(NH4)2(SO4)2.6H2O is dissolved in a slightly acid solution‚ excess oxalic acid‚ H2C2O4‚ is added and the following reaction takes place: Fe(NH4)2(SO4)2.6H2O + H2C3O4
Premium Chemistry Iron Ammonia
References: a) http://en.wikipedia.org/wiki/Reynolds_number b) http://www.engineeringtoolbox.com/reynolds-number-d_237.html c) http://www.engineeringtoolbox.com/laminar-transitional-turbulent-flow-d_577.html d) http://www.slashdocs.com/prqt/lab-report-osbourne-reynolds-apparatus.html APPENDIX The Reynolds Apparatus that was used during the experiment.
Premium Fluid dynamics Fluid mechanics Viscosity
The Virtual Lab – ELISA Test Lab: Immunology 09/04/2013 Instructors: Dr. Charlie Wilson Written by: Dipen Patel I. Objective: The purpose of the lab was to learn the procedure of performing an ELISA test to determine whether a particular antibody is present in a patient’s blood sample. ELISA is an abbreviation for “Enzyme-linked Immunosorbent Assay." II. Introduction: The interaction of antigen and antibody outside the body can be used to determine if patient
Premium Antibody Immune system ELISA