IB Friction Lab Write Up 3. The slope of my graph represents the constant value for myu as the Normal Force and the force of friction are constantly changing. 4. The kinetic slope is the biggest by far because it represents the less coefficient of friction it has to overcome to move easier. 5. According to my data table‚ an increase in weight always‚ without fail‚ creates a greater force of friction. 6. An increase in weight does not affect the coefficient of friction by also increasing
Free Force Friction Mass
Kinetic Friction Experiment #13 Joe Solution E01234567 Partner- Jane Answers PHY 221 Lab Instructor- Nathaniel Franklin Wednesday‚ 11 AM-1 PM Lecture Instructor – Dr. Jacobs Abstract The purpose of this experiment was to examine kinetic friction and what factors affect it. We pulled a wood block across a surface to determine whether the surface area of the block or the type of surface affects friction. The surface area did not appear to affect friction‚ since there was a small percent difference
Premium Friction Force Classical mechanics
point of the plumb bob‚ and this value was used for the radius. We then measured how long it would take the plumb bob to complete ten full rotations‚ which was used to find the frequency of this experiment. Questions & Answers 1. The purpose of this lab is to examine objects in circular
Premium Force Mass Classical mechanics
orientation of a piezoelectric material during the design and manufacture of a device. There are certain mechanical parameters which plays a great role in piezoelectric effect. 2.2.1 Mechanical Strain The mechanical strain S which results from the application of a stress T is linearly proportional to the compliance S (S-1= Young’s modulus) within the elastic deformation region of the stress-strain curve of the material (below the yield strength )
Premium Force Elasticity Mass
Gather all of your equipment‚ a LabQuest 2‚ two friction blocks (one with sandpaper and one with foam)‚ a force sensor‚ slotted masses‚ a ruler‚ and two sheets of graph paper. Weigh the two friction blocks in kilograms. Then multiply that number by g‚ 9.8‚ to find the blocks’ weights in Newtons and record it. Plug the force sensor into channel 1 of your LabQuest 2‚ this allows you to calculate the amount of force that you pull the block with. Choose six of the slotted masses to place on the blocks
Premium Mass Force Classical mechanics
Clutch Objective: The Aim of this experiment is to find the relation between the axial load W and the frictional torque T‚ using a single plate clutch. To find the coefficient of friction between the clutch surfaces using the uniform wear theory. To experimentally conclude whether the average radius of the friction plate is proportional to the frictional torque. Apparatus used: Weights‚ String Plate clutch Hangers Pulleys 5 x 2kg weights for axial load Theory: It is stated theoretically
Free Force Friction Mass
Hypothesis: For an increase in a normal force‚ there will be a corresponding increase in friction. Introduction: Force is usually connected with a push or pull exerted on an object. In this experiment‚ I am using a contact force‚ a force that exists from physical contact between two things. I am pulling the spring scale‚ which measure force in Newtons (kg x m/s2)‚ and then the block is moving. Different masses (kg)‚ or the measure of the resistance of an object to changes in its motion due
Premium Force Classical mechanics Mass
DESCRIPTION The Centripetal Acceleration lab consists of using a pendulum bob swinging continuously. This will help see the F_max(tension) and F_(mean )(weight of the pendulum)‚ net force (N) and v_mean(velocity). RESULTS When starting the lab the first thing to do is to measure the cylinder properties (the bob) in table one. The measurements were: diameter (D) is .0815m‚ height (H) is .025 m‚ mass is .06591 kg‚ and the 〖Weight〗_theory W is .645918 Mg‚N. Second thing to do is to launch from
Premium Force Classical mechanics Mass
blah i just want to be able to read this essay so I’m sorry if this isdissappointing to you hold on Physics Pre-AP Projectile Motion Lab Report Purpose The purpose of this lab was to determine how angle and gravity affects velocity and range. Procedure Materials Projectile launcher Marble Two measuring sticks Tin foil Pencil Procedure Set the angle of the projectile launcher to 30 degrees (make sure that the bottom of the launcher is even with the desk). Put the marble inside the
Premium Angle Archimedes Force
CLUTCH | 1. INTRODUCTION Friction is to be avoided in some parts of machines‚ but is wanted in such items as clutches‚ brakes and belt-driven pulley systems. The apparatus used for this experiment is a simulation of a clutch‚ the pressure being provided by vertical weight on a plate. In engaging a clutch between a running engine and a stationary machine there is bound to be some wear‚ and it is evident that the wear must be uniform on the surface of the friction plate. As wear is proportional
Premium Friction Force