Lab Report 1 Introduction: Proper chemical formulas entitle many challenges such as the Law of Multiple proportions that states that there may be more than one plausible mole ratio for the elements in that compound. However if we determine the mass of each element in the compound we will be able to get the true chemical formula. In this experiment‚ we used the law of definite proportions to find the chemical formula for a hydrated compound containing copper‚ chlorine‚ and water molecules
Premium Chlorine Water Ion
Example lab report of Synthesis of potassium tris (oxalato) ferrate (III) trihydrate Posted by Nurul Yunaliyana Experiment 5: Synthesis of potassium tris (oxalato) ferrate (III) trihydrate Purpose: to synthesis potassium tris (oxalato) ferrate (III) trihydrate ‚K3 [Fe (C2O4)3].3H2O. Introduction: Ferrous ammonium sulfate‚ Fe(NH4)2(SO4)2.6H2O is dissolved in a slightly acid solution‚ excess oxalic acid‚ H2C2O4‚ is added and the following reaction takes place: Fe(NH4)2(SO4)2.6H2O + H2C3O4
Premium Chemistry Iron Ammonia
concentrations of solutes in and out of the cell. Filtration is what is used to remove solid particles and they can be removed by passing through a liquid and gas. The information above is very important because it is exactly what everything in this lab will be about. It explains in detail what every single little definition and important
Premium Osmosis Diffusion Membrane biology
# Now You See It – Copper Cycle Lab The purpose of the lab is to discover what happens when someone executes a series of procedures‚ beginning with copper metal. What is done | What is observed | 1. Started with copper‚ Cu (s). | reddish‚ brownish‚ orange-ish‚ powder-like | 2. Added nitric acid‚ HNO3 (aq). | acid turns blue and smells like chlorine. | 3. Added water‚ H2O (l). | stayed the same | 4. Added sodium hydroxide‚ NaOH (aq). | changed consistency‚ gel-like | 5. Heated the
Premium Sulfuric acid Copper Zinc
listed below. You must observe and analyze these as part of the lab. The Iced Tea Debate The Salty Soup The Fire Bug 2 Use the DATA chart provided for recording observation based on three demonstrations you will watch 3 Watch each part of the experimental demonstration and make preditions about wht will happen in each scenario . Record your preditions and observations in the Data an Observations section of your labatory report format. Problem: How can matter and energy be described in
Premium Energy Conservation of energy Chemistry
Wave Nature of Light Objective: The purpose of this lab is to investigate interference‚ otherwise known as the diffraction of light. A beam of light acts a wave‚ and we are able to use equations so calculate the wavelength of the light used. The diffraction of a straight edge demonstrates that light waves bend around straight edges‚ allowing light to enter an area of shadow. When waves are superposed‚ they reinforce each other when crests are in phase and cancel out when they are not in phase
Premium Diffraction Wavelength Light
Microbiology-2460 Lab-003 March 31‚2008 Lab Report-Escherichia coli Abstract The purpose for this lab report was to identify and inform of an unknown bacteria that has been causing a patient to have lower abdominal and pelvic pain. To obtain the identification of this unknown bacterium‚ several biochemical tests needed to be performed in order to prescribe the correct medication to treat and cure the symptoms. Introduction In a lab today‚ I am to identify an unknown bacterium that is
Premium Escherichia coli Bacteria
Solute Concentration of Potatoes Lab #1 Purpose: To find the molarity/concentration of potato cytoplasm. Materials: As on page 1 in the lab handout. Procedure: As on page 1 in the lab handout. Data and Observations: Test Tube # | Concentration of sucrose solution (mol/L) | Initial Mass (g) | Final Mass | Percentage change in mass | 1 | 1.0 mol/L | 3.00g | 2.25g | -25.0% | 2 | 0.9 mol/L | 2.70g | 2.07g | -23.3% | 3 | 0.8 mol/L | 2.92g | 2.25g | -22.9% | 4 | 0.7 mol/L | 2.60g
Premium Concentration Osmosis Chemistry
responsible for making the pillbug habitat‚ taking them in and out of the habitat for our experiment‚ setting up the experiment setups for testing‚ and timing the experiment. In my opinion‚ I contributed a lot in my group. I did a majority of the lab proposal‚ and a substantial amount in the lab report. I was always the one getting up to gather our materials and pillbugs from the bins and making sure that our experiment was going as smoothly as intended. From this project‚
Premium Scientific method Project management Management
MEC 325/580 Lab Report CNC Machining Lab Report Date: March 18‚ 2013 Group Leader: Jian Wu Team Members: Group Number: G4 Regment No.: D Insturctor: CONTENTS 1.Objective and introduction. 2.Principles and practice. 3.Design and result. 4.Conclusion and recommendations. Appendices 1. Objective and introduction * Objectives Operate the CNC milling machine using G-codes‚ M-codes in a CNC program. * Equipment: Minitech CNC machine (Series 2) * Machine
Premium Milling machine Numerical control