solution to create linear supramolecular assemblies containing thousands of ordered pairs‚ even without the need for purification.5 With available noncanonical nucleobases to pick from‚ and evidence of depsipeptides that could be formed in prebiotically plausible ways‚ David Fialho and Nicholas Hud designed CyAspAmide (ψD). This prebiotically plausible proto-nucleic acid monomer (Figure 1)‚ is the amide formed between a cyanuric acid-functionalized hydroxy acid called 2-OH-CyCo4 (abbreviated as
Premium Amino acid Protein Oxygen
Physics Lab report Aammar Paracha Section MX Feb 6th 2015 OPTICS Abstract: This experiment revolves around using light rays and lenses. The experiment also discusses different properties of light rays. This experiment uses different lenses and measurements to produce images and observes different techniques to obtain the image position. Question and Answers: 1. Use your data to verify the Law of Reflection and then use Snell’s Law to calculate
Premium Optics Lens
’Neil 2002). The particular conditions that had to exist for this to apply were that the population had no mutation‚ had no natural selection‚ was a large population‚ had only random mating‚ and had no migration. For the cases to follow later in the lab‚ Cases 1 and 2 exemplify Hardy-Weinberg conditions. All of the others either have selection or not enough members in the population‚ which will be the most-closely observed
Premium Biology Experiment Evolution
Raquel Johnson October 19‚ 2014 Solids: Recrystallization and Melting Points Organic Chemistry 2423 Lab Report: Recrystallization Abstract: The purpose of this lab was to purify an unknown compound by recrystallization. Taking an unknown compound and identifying it by purifying it from its impurities through the use of hot gravity filtration. Then to determine the unknown you were to take the melting point. An unknown compound was recrystallized from hot water to produce 0.99 grams (67% recovery)
Premium Temperature Solubility Solid
Introduction and Purpose: This lab focuses on how weight affects the time it takes for a rotocopter to fall from a drop height of 1 and 2 meter(s) respectively. The primary goal of this lab is to investigate and explain the relationship of these two factors. During the process of conducting this experiment‚ learning to design a lab will also be achieved. Research Question: What is the effect of weight on the time it takes for a rotocopter to fall from a drop height of 1 and 2 meter(s)? Variable
Premium Force Classical mechanics Mass
Impurity Lab Report Aim: To find out the difference of the boiling point and melting point when adding impurity (salt) to water. Diagram: Method: 1.Set up the apparatus as shown in the diagram 2. Get a known amount of ice in the beaker (half full)‚ and a known amount of salt in another beaker 3. Measure the temperature (melting point) of the ice without adding any impurity (salt). 4. Measure the temperature (melting point) of the ice after adding the salt into the beaker. 5. Heat up
Premium Water Solid Fahrenheit
Pseudomonas taiwanensis – Enrichment‚ Isolation and Identification Microbiology 521 2/10/12 Purpose: The purpose of this experiment was to enrich Pseudomonas bacteria‚ isolating a species of Pseudomonas and identifying it using phenotypic properties and DNA sequencing as an existent or completely new and undiscovered species of Pseudomonas. Overview: Genus Pseudomonas is a chemoheterotrophic bacteria found in soil and water. They are Gram negative‚ motile‚ paired rods that are also oxidase-positive
Premium Bacteria Microbiology Escherichia coli
Lab Report Procedure 6.1: Perform Benedict’s test for reducing sugars. Introduction: Benedict’s tests allows for the detection of the presence of reducing sugars. All monosaccharides are reducing sugars since all of them have active carbonyl group. Some disaccharides that are exposed to a carbonyl group are also reducing sugars but less reactive than monosaccharides. By mixing the sugar solution with Benedict’s solution and heating them‚ a redox reaction will occur. The copper (II) sulphate
Free Glucose Carbohydrate Sucrose
Lab Report Density Name: Period: Problem How do you calculate Density? What units did you use for volume‚ mass‚ and density? When the cubes are placed in water which one will sink 1st? What is the ranking of the cubes lightest (1) to heaviest (10)? Is it true that the cube with the most mass will have the most density? Hypothesis I think the 1st cube was aluminum I think the 2nd cube was steel I think the 3rd cube was brass I think the 4th cube was copper I think the 5th
Premium Density Volume
ABSTRACT On the past two weeks‚ I have done an experiment on hydrostatics‚ or is also known as fluid statics (fluid at rest) within the fluid mechanics field of study. This condition explains that in a stable condition‚ the fluid is at rest. The use of fluid in doing work is known as hydraulics‚ and the science of fluid in motion is known as fluid dynamics. INTRODUCTION The natural nature of fluids are they cannot remain stationary under the application of shear stress. However‚ fluid
Premium Fluid mechanics Force Fluid dynamics