1. Title: The Process of Determining the Unknown Bacteria #9 Rachel Judecki July 5‚ 2011 2. Introduction: Each student was given unknown bacteria and was instructed to perform a variety of experimental tests that would help to identify their bacteria. During the process of identification‚ the unknown bacteria was added to many different testing medias using aseptic technique. They are as follows: lactose fermentation on eosin methylene blue (EMB)‚ TSI (Triple Sugar Iron agar)‚ Phenol
Premium Escherichia coli
Lab Report 3 In this lab‚ we will take a trip to the planetarium lab and will learn about Right ascension and declination‚ and altitude and zenith. After looking at the different points shown‚ we will log the altitude and zenith in the chart in our lab manual. Now we will look at the same points and label the right ascension and declination. Then we will learn about the easiest way to locate the star Polaris. As we started the first program‚ we answered a few questions to make sure we knew
Premium
Name SOLUBILITY CURVES Answer the following questions based on the solubility curve below. Which salt is least soluble in water .. at 2O° C? 2. How many grams of potassium chloride can be dissolved in 200 g of water at 80° C? IO 3. At 40° C‚ how much potassium _ __nitrate coin be dissoiu$tl ^n 30D.g of water? ------W- ’1 80 70 ...- O --60 0 5© 40 4. Which salt shows the least change 30 In solubility from 0° - 100° C? 20 10 At 30° C‚ 90 g of sodium
Premium Solubility Ammonia Solution
Gram Stain: The important part of this experiment is being able to determine a bacterium based on its cell wall structure. It also helps indentify if the unknown organism is a Gram positive or Gram negative. This is the initial step that must be taken before any other lab procedure may continue on to ensure the purity is present‚ the arrangement of the cells‚ and the shape the cell has. The staining of the cell starts off with using the primary stain‚ Crystal Violet which is a purple color‚ to begin
Premium
This lab report will be detailing the steps taken and the results discovered when using spectrophotometry to determine the percentage of copper in a copper-clad penny and the thicknes of the copper layer on the copper-clad penny. After 1982‚ copper coating has been used in the creation of the penny because the cost of pure copper has increase to the point that the amount needed t omake a penny cost far more than the actual value of the penny. This lab allowed us to see just how much copper coating
Premium Chemistry Spectroscopy Ammonia
Investigation Investigate the amount of heat evolved when magnesium reacts with dilute acids. Planning What I am going to do I am going to find out how much heat is given out when magnesium reacts with a variety of dilute acids. In order to make comparisons between the acids‚ I shall use my results to work out how much heat would be given out if 1 mole of magnesium reacted with an excess of each acid. The acids I shall use are hydrochloric acid‚ sulphuric acid‚ nitric acid and ethanoic acid
Premium Hydrogen Sulfuric acid Acid
Page I - Cover sheet In the middle f the page give name and number of your microorganism In the right lower corner provide - your name - Lab section number (Biol 108-005) - Date submitted ( 4/18/2013) - the unknown tube # is 5 Page II table of result - This page will have your table of results include the following information - Name of the test - Medium used - Indicator used - your results Part III - All the test done As many pages as needed to do a complete job. in this section
Premium Organism Bacteria Biology
** Introduction : A medical microbiology lab performs testing on human samples collected from different body sites. The tests are used to detect and identify any microorganisms capable of causing disease. Knowing of unknown microorganism is important on how this microorganism works and how it is structured‚ means knowing how it can affect humans. The purpose of this study was to identify an unknown bacterium by applying all methods that were previously conducted and learned in the medical microbiology
Premium Staphylococcus Bacteria Staphylococcus aureus
Enterobacter cloacae are responsible for various infections such as bacteremia‚ lower respiratory tract infections‚ skin and soft tissue infections‚ urinary tract infections‚ endocarditis‚ intra-abdominal infections‚ septic arthritis. Enterobacter cloacae infections that target the bladder and urinary tract may cause pain or an uncomfortable pressure. Many people suffering from a urinary infection with Enterobacter cloacae complain of a frequent urge to urinate‚ pain or burning while urinating‚ and
Premium
MEC 325/580 Lab Report CNC Machining Lab Report Date: March 18‚ 2013 Group Leader: Jian Wu Team Members: Group Number: G4 Regment No.: D Insturctor: CONTENTS 1.Objective and introduction. 2.Principles and practice. 3.Design and result. 4.Conclusion and recommendations. Appendices 1. Objective and introduction * Objectives Operate the CNC milling machine using G-codes‚ M-codes in a CNC program. * Equipment: Minitech CNC machine (Series 2) * Machine
Premium Milling machine Numerical control