molecules as a part of their crystal structure. We call such solids hydrates‚ and we call the bound water the water of hydration. A hydrate has a definite number of water molecules bound to each anhydrous salt unit. The formula of the hydrate copper(II) sulfate pentahydrate is CuSO4 · 5 H2O The dot indicates that the molecules of water are attached to the ions in CuSO4 by weak bonds. We can drive off the water of hydration by heating the hydrate. If blue CuSO4 · 5 H2O is heated‚ the water of hydration
Premium Molecule Water Chemistry
Title of the Experiment: determination of densities Introduction The density of a sample of matter represents the mass contained within a unit volume of space in the sample. For most samples‚ a unit volume means 1.0 ml. The units of density‚ therefore‚ are quoted in terms of grams per milliliter (g/ml) or grams per cubic centimeter (g/cm3) for most solid and liquid samples of matter. Density is often used as a point of identification in the determination of an unknown substance. The density
Premium Density Volume Temperature
Determination of g by Free Fall Raw Data: Time (ms) ± 0.01ms Height of release of ball from the sensor plate (cm) ±0.1cm Trial 1 Trial 2 Trial 3 Trial 4 Trial 5 0.0 0.00 0.00 0.00 0.00 0.00 15.0 180.05 179.36 178.74 180.26 180.23 30.0 244.33 244.21 244.71 243.88 245.87 45.0 300.72 301.29 300.59 301.43 301.70 60.0 348.68 348.39 348.77 349.12 348.35 75.0 390.27 390.77 389.58 391.19 390.43 This table below is the results obtained during the experiment in cm/ms. This table below is the results
Premium Measurement Numerical analysis Standard deviation
Solubility Product Determination Purpose • To determine the solubility product constant‚ Ksp‚ of an ionic compound. Introduction The solubility product constant‚ Ksp‚ is a particular type of equilibrium constant. The equilibrium is formed when an ionic solid dissolves in water to form a saturated solution. The equilibrium exists between the aqueous ions and the undissolved solid. A saturated solution contains the maximum concentration of ions of the substance that can dissolve at
Premium Chemistry Solution Solubility
SynopsisThe objective is to determine the amount of Sulphate in anhydrous Barium Sulphate precipitate by gravimetric method. Gravimetric method is by the quantitative determination of the mass of anhydrous Barium Sulphate precipitate. Barium sulphate precipitate is form when Barium Chloride is added excessively to a hot given Sulphate solution slightly acidified with concentrated Hydrochloride acid. The white precipitate of hydrate Barium Sulphate formed is than digest‚ filtered out‚ washed and dried
Premium Solubility
Enhanced spectrofluorimetric determination of Mebendazole‚ a benzimidazole anthelmintic drug‚ through complex formation with Lanthanum (III)‚ in pharmaceutical preparations and spiked human plasma Abstract The article concerned with the development of simple‚ sensitive‚ rapid and specific spectrofluorimetric procedure for determination of mebendazole. The cited drug was reacted with lanthanum (III) ions to produce highly fluorescent stable complex measured at 340 nm after excitation at 295 nm. Different
Premium Chemistry Solvent Acetic acid
UNKNOWN SAMPLE #97 COMPLEXOMETRIC DETERMINATION OF WATER HARDNESS DR. BUDRUK CHM 152 LL SEAN MARKIS 4 FEBRUARY 2015 Introduction Using a Lewis base neutral molecule to donate electron pairs (ligands) to a Lewis acid metal ion center to form a single cluster (complex) ion. When the complex ions forms with a metal ion (chelation) the ligand used is called the (chelating agent). EDTA acts as a great chelating agent due to the Nitrogen and Oxygen donating an electron pair to the
Premium Water Calcium Titration
Ammonium sulfate foreign producers 1. Highlights One of the largest producers of specialty chemicals‚ fertilizers‚ plastics and packaging in Latin America. Major producer of styrene and polystyrene. Latin America’s sole producer of acrylonitrile (AN)‚ methyl methacrylate (MMA)‚ acrylic and polycarbonate resins‚ polycarbonate films and cyanides. Largest producer of cast acrylic sheets in the Americas. Latin American’s largest ammonium sulfate producer http://www.unigel.com.br/
Premium Chemical industry Nitrogen Chemical reaction
DETERMINATION OF BOILING POINTS Introduction: The boiling point of a compound is the temperature at which it changes from a liquid to a gas. This is a physical property often used to identify substances or to check the purity of the compound. It is difficult‚ though‚ to find a boiling point. Usually‚ chemists can only obtain a boiling range of a 2 - 3oC accuracy. This is usually sufficient for most uses of the boiling point. Purpose: The purpose of this experiment is to determine the
Free Gas Temperature Water
Jahzeel Morales Jessa Arellano September 19‚ 2014 Period 4 Lab #1: Density Determinations for Solutions Theory: The density of a sample of matter is very useful when trying to find the identity of an unknown substance. The units of density are quoted in (g/mL) for liquid samples of matter. For that reason if the volume is known of a liquid‚ determining its density is easily determined by weighing it accurately. Density can also be used as a tool for finding the concentration of solutions
Premium Solution Concentration Volume