This report demonstrates calorimetry‚ or the technique of measuring heat effects in the surroundings. In order to make sure that there is no temperature change‚ or that it is an isothermal heat transfer‚ it is kept at a similar temperature in an ice bath. By knowing the change in volume‚ the density of ice‚ and the density of liquid water‚ it is presumed that then you could decipher the mass of the ice that melted. With this‚ it is possible to understand the transfer of heat from this chemical equation
Premium Thermodynamics Energy Heat
Experiment 1: Calorimetry INTRODUCTION In the calibration of the calorimeter‚ the net ionic equation used is H+(aq) + OH-(aq) H2O(l). The reaction released heat and is said to be exothermic. HCl is the limiting reactant of the reaction and o.oo5 moles of it was used. The heat generated by the reaction is 55.8 kJ. The sign of T of the reaction used for calibration is opposite to that of H. In the determination of heats of reaction‚ the reaction of 15 mL 1 M CuSO4 + 0.05 g Zn produced a
Premium Enthalpy Chemical reaction Thermodynamics
06.03 Calorimetry: Lab Report Before You Begin: You may either copy and paste this document into a word processing program of your choice or print this page. Part I The Dissolving of Solid Sodium Hydroxide in Water Procedure: 1. Measure out approximately 200 mL of distilled water and pour it into the calorimeter. Stir carefully with a thermometer until a constant temperature is reached. Record the volume of water and the constant initial temperature of the water on your data table.
Premium
1. Clean‚ rinse‚ and fill a buret with NaOH solution just as you did in last week’s experiment. Record the molarity of the NaOH and the initial NaOH volume reading from the buret (+0.02 mL). 2. Weigh an antacid table in a weighing boat and record the mass (+0.01 g). Transfer the tablet to a clean mortar and crush the tablet into a fine powder using the pestle. 3. Weigh about 0.2 grams (+0.01 g) of the ground up tablet powder and transfer it to a clean 250 mL Erlenmeyer flask. 4. Transfer
Premium Chemistry Water Titration
1. Start off by weighing two paracetamol tablets using some accurate scales. Record the mass down (1.15g). This had to be as accurate and precise as we could get it so we had the correct weight to start the experiment. Without this then the results we found at the end would not be accurate. A problem that could be faced with this is that the scales may not have been fully set to zero. Also it takes time for it to fully reach its weight on the reading so you may move them too quick before the right
Premium Water Chemistry Oxygen
Calorimetry Experiment Purpose: The objective of this lab is to determine the enthalpy change for NaOH(aq) + HCl(aq) NaCl (aq) + H2O(l) Procedure: Before measuring the enthalpy of acid base neutralization‚ my partner Brian and I determined a calorimeter constant‚ using a homemade polystyrene calorimeter. With the following formula and data: qhot= cm (Tf-Ti) qcold=cm(Tf-Ti) SYSTEM DATA SURROUNDINGS DATA Water cold Mass: 50mL Water hot Mass: 50mL C=4.18 C=4.18 Ti=20 C Ti=31
Premium Sodium hydroxide Chlorine Calorimetry
CALORIMETRY KATHLEEN IVY B. MENDOZA DEPARTMENT OF CHEMICAL ENGINEERING‚ COLLEGE OF ENGINEERING UNIVERSITY OF THE PHILIPPINES DILIMAN‚ QUEZON CITY DATE PERFORMED: JANUARY 30‚ 2015 INSTRUCTOR’S NAME: JACOB NOEL M. INGUITO INTRODUCTION Calorimetry‚ derived from the Latin calor meaning heat‚ and the Greek metry meaning to measure‚ is the science of measuring the amount of heat‚ q.1 The amount of heat is absorbed (endothermic where qrxn >0) or released (exothermic where qrxn <0) by the system with
Premium Heat Heat transfer Thermodynamics
In this experiment‚ we used acquired observational data to develop an activity series describing the relative reactivity of the metals being tested. The elements within a periodic table often show different trends in physical and chemical properties depending on the period or group they are apart of. In a periodic table‚ elements are arranged by increasing atomic number in horizontal rows called periods. The atomic numbers represent the number of protons in each element. The periodic table is also
Premium Chemistry Chemical element Periodic table
Aim: The aim of this experiment is to convert copper metal through a series of intermediate copper compounds back into copper metal. By weighing the copper at the beginning and at the end of the experiment the percentage yield can be determined. Method: The experiment was carried out as outlined in the practical manual. Results: Table: showing masses: Mass copper wire 0.2510 Mass crucible 28.9257 Mass watch glass 19.6213 Mass watch glass + copper 19.7890 Mass copper
Premium Chemistry Copper Chemical reaction
To begin the experiment‚ the unknown needs to be determined as an acid or a base by using litmus paper or a pH strip. For the rest of the experiment‚ if the substance is being handled‚ gloves and goggles must be worn. Use a clean and dry Erlenmeyer flask and weigh it. Then‚ some of the unknown will be measured and poured into the flask. Also way the flask and the unknown. Add distilled water and phenol saline to the flask. Set that aside to prepare the biuret. Choose the substance that will be used
Premium Chemistry Chemical substance Oxygen