Steel and heat treatment MILD STEEL Mild steel is also called plain carbon steel. It is the most common type of steel and it price is pretty low. Its composition is around about 0.05%-0.29% carbon content. Mild steel has a relatively low tensile strength but the surface can be hardened through carburizing. It is mostly used where large amounts of steel needs to be formed eg structural steel MEDIUM CARBON STEEL Medium carbon steel has great wear resistance and is used for forged automotive
Premium Steel
SEWAGE TREATMENT CONTENTS:- ❖ Introduction ▪ What is Sewage? ▪ Why do we need Sewage Treatment? ▪ What is Sewage Treatment? ▪ What does Sewage Treatment involve? ❖ Levels of Waste Water Treatment ▪ Preliminary Treatment ▪ Primary Treatment ▪ Secondary Treatment ▪ Tertiary/ Advanced Treatment ❖ Other Process Required after Water Treatment ▪ Disinfection ▪ Sludge Treatment and Disposal ❖ References
Premium Sewage treatment Anaerobic digestion Wastewater
Heat resistance of endospores of Bacillus pumilus Abstract Spore suspension of Bacillus pumilus was inoculated into universal bottles containing sterile distilled water in water baths at temperatures of 85°C‚ 90°C and 95°C. At specific time intervals‚ a sample was removed and spread on nutrient agar plates. The number of colonies formed was used to determine the D-value and z-value. The D-value for 85°C is 64.1 minutes‚ 25.7 minutes for 90°C and 8.2 minutes for 95°C while the z-value is 11
Premium Heat Bacillus Bacteria
Abstract Precipitation hardening‚ or age hardening‚ provides one of the most widely used mechanisms for the strengthening of metal alloys. It influences some properties of the alloys such as strength‚ hardness and ductility. The purpose of this experiment was to test the effect of temperature and aging time on strength and hardness of 6060 aluminium alloy samples that have roughly similar compositions by subjecting them to different temperatures for different periods of time. The experiment showed
Premium Tensile strength
Activated Sludge Process will encompass * Design of aeration basins. Relevant design parameters are * BOD load from the upstream process * Mixed Liquor Suspended Solids Concentration (MLSS – mg/l) – typically 2‚000 to 4‚000 * Sludge Age 5 to 25 days * Sludge settleabiltiy (SVI ml/g) typically 100-120 * Process Oxygen Demand (POD) * Generally fine bubble diffusers used in modern plant design – actual oxygen transfer efficiency dependent
Premium Sewage treatment Activated sludge Wastewater
which had many aspects on their transformation of mechanisms. Microstructure of bainite seems to be darker than the mastenisite under a microscope. The reason behind bainite structure became useful was because of its hardness. There are few Heat treatments that steel can be tested by such as Annealing‚ quenching Harderning‚ and Normalizing. Body Bainite is A combination of ferrite and cementite in ferrous metals that is harder than pearlite. Bainite contains needlelike grain structures‚ and
Premium Steel Austenite
of the metal was determined by the heat energy calculations. The heat capacity that was found matched closely to that of the lead. There were several possible sources of error that could be found throughout the lab. Some of the main errors as seen in question 7 that could have affected the results of the lab were the amount of water transferred with the hot metal‚ the metal cooling off as it was transferred from the calorimeter‚ the calorimeter lost heat to the surroundings as it was stirred
Premium Heat Thermodynamics Specific heat capacity
Project – I DESIGN OF GEOTHERMAL HEAT PUMP A Project Report Submitted By Peter Galimutti (2474762) Neeraj Pastakia (2462895) Balasubrahmanyam Vanum (2474858) (MCE 622: Energy Conversion) MASTER OF SCIENCE IN MECHANICAL ENGINEERING Fall 07 Under the esteemed guidance of Dr.Earnest N.Poulous (Associate Professor) DEPARTMENT
Premium Heat
as an alternative water source. This results in an independent water source which through treatment can provide consistent quality water. Canal water is sent through a water treatment process with unused water sent back to the source with little environmental impact. The scope of this project is to assess the environmental impact of an onsite water treatment facility. Chapter 2. Overview of Water treatment Process design 2.1 Design process The feed water will pass through 20 micron media filter
Premium Water management Water purification Water treatment
MECHANICAL ENGINEERING 449 SENIOR LAB Test of a Heat Pump Submitted Submitted by: Submitted to: Executive Summary: The purpose of this experiment was to determine the performance values of a Hylton Air and Water Heat Pump System. The system uses refrigerant 134a and water as the working fluids. The power input of the system was measured. The rate of heat output and the coefficient of performance are to be determined
Premium Thermodynamics Heat Heat pump