Title: Lab #3 Separation of a Mixture of Solids Purpose: To understand the different separation methods and techniques that depend on the chemical properties of a specific substance. Also to become more comfortable with performing those actions of separation so I have them in the future. For this experiment‚ I will separate a mixture of four distinct substances: sodium chloride‚ benzoic acid‚ silicon dioxide‚ and iron fillings into pure beings. Procedure: Materials: distilled water coffee
Premium Water Mass Weight
A safety audit for the gas-solid fluidization experiment was conducted. The following safety concerns were found when performing the audit: operating beyond the operating limits‚ spillage of the beads‚ risk of head injury from bending over to change the beads in the apparatus or from the low bar‚ and congestion of the workspace. One of the biggest safety concerns with this lab involved the small glass beads that acted as the solid in the experiment. If the gas flow rate goes below 50 standard cubic
Premium Glass Risk Causality
Title: Separation of a Mixture of Solids Purpose: Learn and demonstrate how to separate different ingredients from a mixture of solids using different methods based on the properties of each ingredient. Procedure: I weighed mixture and tools‚ and proceeded to begin separating each ingredient. I used a magnet to separate the iron from the mixture. Then I heated the mixture in water to get the non-soluble sand out. Then I filtered out the benzoic acid after cooling it into a crystal form
Premium Water Evaporation
Faculty of Advanced technology Project Report For the Project of Reverse Engineering of Complex Geometry Components Submitted by: Md Moonzoor Morshed Supervisor: Dr. Jafar Jamshidi University Enrolment Number: 09160906 Submitted on: Sunday‚ 23 March 2014 Abstract This research proposes the methodology of Reverse Engineering to repair complex geometry components. The work contains algorithms and techniques of digitizing‚ assessment analyses‚ and surface renovation
Premium Engineering
service-based city due to the massive developmental activities of Iskandar Malaysia project city plan. However‚ the rapid development in Johor also indicated that the generation of solid waste will increase significantly. For this reason‚ Abba et al. (2013) conducted a case study to assess the environmental impacts of municipal solid waste of Johor by analytical hierarchy process. The assessment is conducted in the city of Johor Bahru which involved Municipals of Johor Bahru Tengah‚ Johor Bahru municipal
Premium Recycling Waste management Waste
Municipal Solid Waste Management in China January 2007 Lin‚ Jiaoqiao Lin‚ Na Qiao‚ Liming Zheng‚ Jie Tsao‚ Chi-Chung Part 1 MSW Management in China Mainland INTRODUCTION No country has ever experienced as large or as fast an increase in solid waste quantities that China is now facing. In 2004 China surpassed the United States as the world’s largest waste generator‚ and by 2030 China’s annual solid waste quantities will increase by
Free Waste management Recycling Waste
Lab 2 “Separation of a Mixture of Solids Lab Report Assistant (10 points) Data Table 1: Experimental Data Grams Percent of mixture Iron (Fe) fillings 0.9 g 20 % Sand 1.2 g 25 % Table salt 1.6 g 25 % Benzoic acid .8 g 16 % Total 4.5 g 86 & Questions A. How did your proposed Procedures or flow charts at the beginning of this experiment compare to the actual Procedures of this lab exercise? (2 points) I proposed a magnet would be the used to remove the iron from
Premium Water Separation process Distillation
Most people knows that solids control is important for the oilfeild drilling industry‚but less people knows the working principle of solids control equipment. Solids control is a technique that uses combined equipment for drilling rigs to separate the solids in the drilling fluids that are crushed by the drill bits and carried out of the well to the surface. The solids control equipment contains five stages‚which including mud tanks‚shale shakers‚vacuum degassers‚ desanders‚ desilters and
Premium Drilling rig Drill Petroleum engineering
The Little Heat Engine: Heat Transfer in Solids‚ Liquids and Gases The question now is wherein the mistake consists and how it can be removed. Max Planck‚ Philosophy of Physics‚ 1936. While it is true that the field of thermodynamics can be complex‚1-8 the basic ideas behind the study of heat (or energy) transfer remain simple. Let us begin this study with an ideal solid‚ S1‚ in an empty universe. S1 contains atoms arranged in a
Premium Temperature Energy Heat
H83 CEL – CHEMICAL ENGINEERING LABORATORY PROJECT TITLE: SOLID LIQUID EXTRACTION OF GANODERMA LUCIDUM NAME: WIJETUNGE MUDALIGE DINITHI ISHARA WIJETUNGE ID NO: 007118 SUPERVISOR: DR SIVAKUMAR MANICKAM GROUP MEMBERS: KOW NIEN WEI AAZRA OUMAYYAH PANKAN JASON HEW YIP SENG DATE: 30 APRIL 2012 H83 CEL Chemical Engineering Laboratory Solid Liquid Extraction of Ganoderma Lucidum Author: W.M.Dinithi Ishara Wijetunge I certify that: (i) Apart from the experimental results reported in the
Premium Ultrasound