DESIGN LAB Factors Affecting the Solubility of a Solid in a Liquid In this experiment‚ my goal is to determine the affect of temperature in the solubility of a solid in a liquid. Research Question: How does the change in the temperature affects the solubility of a solid in a liquid? Independent variables: Temperature of the Solution Dependent variables: The solubility of the solid substance Controlled Variables: * The pressure of the room. * The mass of zinc chloride
Free Solid Liquid Water
AL Physics Centripetal Force(1ST Lab Report) Objective : To measure the centripetal force by whirling it around a horizontal circle‚ then compare the result with theoretical value FC = m(2r. Apparatus : 1Rubber bung 1Glass tube (About 15 cm long) 1Slotted weights‚ with hanger 12 × 0.02 kg 1Nylon thread 1.5 m 1Paper marker 1Adhesive tape 1Metre rule 1Stop watch 1Safety goggles Set-up: Procedure: 1. Attach one end of a 1.5 m length of nylon thread to a rubber bung and thread
Premium Force Classical mechanics Mass
“The Domino Effect” Teacher’s Prompt Investigate the domino effect with a set of dominoes. Aim To investigate the relationship between the mass of the dominoes‚ and how it impacts the time taken of the domino effect. Independent Variable: The mass of each domino (12.38 g‚ 32.38 g‚ 42.38 g‚ 62.38 g‚ 82.38 g). Dependent Variable: Time taken of the domino effect. Controlled Variable: The number of dominoes used (8 dominoes)‚ the distance between the dominoes (2 cm)‚ the loads used as the initial
Premium Causality Mass Force
Rate of reaction Design Lab Background: Reaction rate is most commonly defined as the speed at which a reaction takes place. This rate can be altered by many factors such as temperature‚ pressure‚ concentration‚ volume‚ or the use of a catalyst. In order for a reaction to occur‚ the atoms must collide in the correct orientation to break the bonds and must also have more energy than the needed activation energy. If their energy is not high enough‚ the reaction will not be able to take place. By
Premium Carbon dioxide Chemical reaction Calcium carbonate
Lung Capacity I. Introduction. The chest contains two lungs‚ one lung on the right side of the chest‚ the other on the left side of the chest. Each lung is made up of sections called lobes. The lungs are soft and protected by the ribcage. The purpose of the lungs is to bring oxygen into the body and to remove carbon dioxide. Oxygen is a gas that provides us with energy‚ while carbon dioxide is a waste product or “exhaust” of the body. | To deliver oxygen to the body‚ air is breathed in through
Premium Lung Oxygen
AP/IB Chemistry Internal Assessment Lab Format The following titles and subtitles (in bold) should be used for your lab report and given in this order within your lab report. Title: choose one to fit your experiment I. Design A. Problem – must be a focused‚ clear research question. B. Hypothesis (When appropriate) • Clear answer to Problem – • Logical rational • your conclusion should address the hypothesis you are giving here. C. Variables
Free Scientific method Measurement Control
Independent Assessment Physics Lab (SL): Cantilever Flexion Cherno Okafor Mr. Ebrahimi SPH4U7 October 21st‚ 2012 Introduction Purpose: The purpose of this Physics Lab is to investigate what factors determine the amount of flexion of the cantilever. Hence‚ the objective is to establish a relationship between the length of a cantilever‚ which may give some insight into the physics of cantilevers. Hypothesis: If one increases the length of a cantilever‚ one would expect there to be an
Premium Orders of magnitude Mass Force
AIM To find the acceleration of an object when falling down from a height in the presence of earth’s gravitational field‚ which is also known as free fall. Air resistance is neglected in this experiment. THEORY As an object is released from a height from the ground under the influence of the Earth’s gravitational force‚ the object will always fall under a constant rate of acceleration. Unlike in space‚ where object will just float around after being released‚ object falling on Earth will always
Premium General relativity Gravitation Measurement
concrete mixture based on the BRE Manual Design of concrete mixtures which is attached to this report. It is then used to produce concrete cubes and prisms. The objective of this experiment is to learn the methods of producing concrete and concrete characteristics as well as comparing the theoretical values of the concrete’s Young’s Modulus with experimental values. Procedure for concrete mix: A concrete mix was designed based on the BRE Manual Design of concrete mixtures. Then‚ a total of 40kg
Premium Concrete
Speed of Sound Lab Report Jamie Cook PHYS 1114: College Physics I Oklahoma City Community College December 10‚ 2013 Purpose: The purpose of this experiment is to measure the speed of sound in air and to determine the effects of frequency on the speed of sound. Apparatus (equipment used): Signal generator: manufacturer- EMCO‚ model number- SS-1‚ range- 20Hz-2MHz‚ least count- 1Hz Frequency meter: manufacturer- DEADALON CORPORATION‚ model number- N/A‚ range-
Premium Sound Speed Wavelength