of Chemical Engineering CHME 426 –Chemical Engineering Laboratory III Title Page (Full Report) Title of the Experiment: Reaction through three CSTR in series Submitted by: Group (4) Section: Female 1. Name: Amina Ali ID: 200550284 2. Name: Duaa Tabarak ID: 200553858 3. Name: Mariam Rustom ID: 200552242 Date of experiment: 31st March‚ 2010 Date of submission: 11th April‚ 2010 Grades: Report presentation………………………………………… /15 Abstract and Objective(s)……………………………………/10 Introduction
Premium Sodium hydroxide Chemical reaction
bromophenol blue(mg/L) 0 2.0 4.0 6.0 8.0 10.0 Absorbance at 590nm (Amax of bromophenol blue) 0 0.182 0.284 0.437 0.583 0.754 0.494 0.573 Absorbance at 460nm 0 0.030 0.041 0.048 0.050 0.055 0.012 0.016 According to Beer Lambert law‚ Absorbance‚ A= λbc λis the molar absorbtivity coefficient in L mg-1 cm-1 b is the path length(in cm) of the cuvette which the sample is contained c is the concentration of the compound in solution‚ in mol L-1 A = λbc is in the form of y = mx where
Premium Solution Curve Concentration
Job Safety Analysis or Job Hazard Analysis All employers have duty of care to individuals‚ staff‚ contractors or third parties in the workplace. It is also a legal requirement that organizations should document any health and safety risks that have been identified in the workplace. Equally‚ it is necessary to record the actions taken to reduce those risks What is a Job Safety Analysis or Job Hazard Analysis? One way to increase the knowledge of hazards in the workplace is to conduct
Premium Occupational safety and health
PHYS113 Lab1: Coulomb’s Law ABSTRACT Performing this experimentation will allow one to investigate the relationship quantitative relationship between the electrostatic force and the distance between charged objects. First a simply observation was made of the electrical forces on two pieces of tape taking note of their attraction and repulsion. This same phenomenon was observed in the experimentation of two charged spheres. Furthermore the we used this experimentation to determine the
Premium Electric charge Inverse-square law
Blake Martinez November 1‚ 2013 Lab Write-up Group: Blake‚ Eric‚ Nadia‚ Fidelia Newton’s Third Law Purpose: The purpose of this lab is to calibrate two force sensors properly. Observe the directional relationship between force pairs. Observe the time variation of force pairs. We need to explain Newton’s third law in simple language. Materials: LabPro Interface Two Vernier force sensors .5kg mass String Rubber band DataMate Program Preliminary: 1. The force of the window
Premium
References: http://webs.mn.catholic.edu.au/physics/emery/measurement.htm#Measurement http://www.digipac.ca/chemical/sigfigs/experimental_errors.htm http://www.tsb.gc.ca/eng/rapports-reports/rail/2011/r11v0057/r11v0057.pdf
Premium Experiment Science Design of experiments
Behavior of Gases and Absolute Zero Determination Lab Report Experiment 4 Introduction In this experiment we measured the relationship between temperature‚ volume‚ and pressure. Objectives: Conduct a set of experiments‚ each of which illustrates a gas law. Gather data to identify the gas law described by each activity. Complete the calculations necessary to evaluate the gas law in each activity. From your results‚ derive a single mathematical relationship that relates pressure‚ volume‚ and
Premium Pressure Temperature Gas
3-difluorobenzene) 3) The absorbance of a 0.0816 M solution of a molecule is measured using a 1.000 cm pathlength cuvette. Two peaks are observed in the spectrum‚ one at = 317 nm (A = 0.1286)‚ the other at = 284 nm (A = 0.7215). Assuming Beer’s law holds A = ac (3.1) what are the values for %T (percent transmission) and a (absorption coefficient‚ in units of L/mol.cm) for the molecule at the above two wavelengths? Also do the following from Atkins. Exercise 9.16b Estimate
Premium Electron Electron configuration Chemical bond
City University of Hong Kong Dept. of Physics & Materials Science AP2104 Mechanics of Solids Laboratory Manual Experiment 1 Pure Bending of a Beam Experiment 2 Torsional Deformations Experiment 3 Yield Criteria for Ductile Materials under Plane Stresses Experiment 1 Pure Bending of a Beam Objective 1. To examine the stresses at various positions of the beam under a constant load of pure bending. 2. To determine the curvature of deflection of the beam. Introduction
Premium Force Torque Shear stress
transformations are that light must be absorbed by a compound in order for a photochemical reaction to take place‚ and that for each photon of light absorbed by a chemical system only one molecule is activated for subsequent reaction. This "photo equivalence law" was derived by Albert Einstein during his development of the quantum (photon) theory of light. Absorption of visible and/or ultraviolet light by a molecule transfers all the energy of the photon to one molecule. This is sufficient energy to excite
Premium Oxygen Sunlight Electromagnetic radiation