Abstract Water “hardness” was analyzed in this experiment‚ through the determination of CaCO3 concentration. This was achieved by the titration of an unknown solution using a standardized 0.1M EDTA‚ and addition of Eriochrome Black T to the unknown‚ to indicate the endpoint of the titration. The average concentration of CaCO3 obtained was 1034 ppm‚ with a standard deviation of 2.4495. The results indicate that the unknown solution can be considered as hard water. Introduction The
Premium Titration Calcium Calcium carbonate
Name: Name of lab partner: Date: Title: Determination of the valency of magnesium Objective: To study the quantitative relationship between the amount of reactant and products of a reaction. A known starting mass of magnesium and the measured collection of hydrogen gas will be used to determine the reaction stoichiometry and the valency of magnesium. Introduction: In Chemistry‚ stoichiometry is the study of the quantitative relationship between amounts of reactants and products of a reaction
Free Chemical reaction Hydrogen Chlorine
CHM 3120L ANALYTICAL CHEMISTRY I LABORATORY REPORT EXPERIMENT: SPECTROPHOTOMETRIC DETERMINATION OF IRON IN DRINKING WATER Name: Steven Adrien Section: 3 Date Experiment Completed: Wednesday‚ July 17‚ 2013 1. Complete the following table Fe(II) stock solution | mass‚ g | 0.1756 | volume‚ mL | 500.0 | MW(Fe(NH4)2(SO4)2 x 6H2O)‚ g/mol | 392.14 | AW(Fe)‚ g/mol | 55.85 | conc. Fe(II)‚ ppm | 50.0 | Use Equation Editor to show how you calculated the concentration of Fe(II)
Free Chemistry
Determination of Chemical Formulae: The Reaction of Zinc and Iodine By Sarah Abstract: The main objective of this experiment was to use to the reaction between zinc and iodine to examine the validity of the Law of Conservation of Mass and the Law of Constant Composition. The Law of Constant Composition was tested by determining the mass of each of the reactants‚ zinc and iodine‚ and comparing their total to the mass of the zinc iodide product plus the excess zinc. The total mass of the reactants
Premium Mass Iodine Zinc
Microbiology Lab Report II Title: Determination of a Bacteriophage Titer Purpose: To determine the number of phage particles or plaque-forming units in a suspension of T4 bacteriophage. Materials: 18 24 hour broth culture of Escherichia coli B. 2 ml suspension of T4 bacteriophages with a titer of at least 10‚000 phages/ml 5 trypticase soy agar (TSA) plates. These should be warmed to 37c before use 5 tubes of soft agar (0.7% agar). Prior
Premium Escherichia coli Microbiology Agar plate
| | 1 | 0.2123 | 0.00 | 42.34 | 42.34 | 2 | 0.2195 | 0.00 | 47.24 | 47.24 | 3 | 0.2049 | 0.00 | 26.65 | 46.65 | After Boiling | 1 | | 31.52 | 32.22 | 0.70 | 2 | | 29.34 | 30.61 | 1.27 | 3 | | 30.61 | 31.52 | 0.91 | Week 2: Determination of Sodium Carbonate in the unknown via titrating using bromocresol indicator Sample number: SC 8 Table 2: Titration of the unknown using hydrochloric acid Trial | Mass of unknown (g) | Burette reading (before boiling) | Final Volume
Premium Titration Hydrochloric acid PH
Experiment 5 Gravimetric Determination of Sulfate Eisman E. Morales TA: Jackeline Pennywiit Chemistry 121 02/14/2011 Purpose: To determine the percent sulfate in a sample using a semimicro scale gravimetric procedure. Procedure: Refer to pages 41-42 of General Chemistry volume 1 Laboratory Experiments by Judith Casey and Robert Tatz‚ Hayden McNeil Publishing‚ 2010 Report Sheet See attached report sheet. Report Questions 1. Explain how your calculated value for percent
Premium Chemistry Solubility Water
PRACTICAL 15: DETERMINATION OF HEAT OF NEUTRALIZATION Data collection: |Reaction |Initial Temperature/°C (±0.25) |Final Temperature of Mixture/°C (±0.25) | | |Acid |Base | | |HNO3 + NaOH |28.00 |28.25 |34.50 | |HNO3 + KOH |28.25 |28.25 |34.00
Premium Sodium hydroxide Thermodynamics Acid
Melting pointe determination #01 Introduction: Objective To learn how to obtain an accurate melting point using a MELTING POINT APPARATUS‚ then use them to draw eutectic curve and determine the eutectic point. Melting point of a solid is the temperature at which the solid and its liquid form are in equilibrium‚ i.e.‚ molecules move back and forth between the two states at the same rate‚ so both phases remain present. If the temperature of a solid is measured carefully as the solid is heated
Premium Melting point Temperature Liquid
Determination of an Equilibrium Constant Abstract: In this experiment‚ two reactions were run to determine the molar absorptivity and the equilibrium constant of FeSCN2+. The main principles used in this lab are equilibrium‚ LeChatlier’s Principle‚ Beer’s Law and Spectrocopy. The first reaction was run to completion using LeChatier’s Principle and the second reaction was run to equilibrium. A spectrophotometer was used to measure absorbances. Using a graph of absorbance versus concentration
Premium Chemical equilibrium Concentration