LABORATORY REPORT I OBJECTIVES The objective of this experiment is to; • Identifying the range and limits of a measuring apparatus. • Rectifying any instrumental error that might be present in an instrument. • Investigating the limits and capabilities of a measuring instrument. • Determining the accuracy of the actual volume of a volumetric pipette‚ volumetric flask & measuring cylinder. INTRODUCTION The purpose of this experiment is to investigate the measurement of the actual volume
Premium Metrology Laboratory glassware Test method
Copper Sulphate Calibration Aim The objective of this experiment is to determine the unknown concentrations of solutions. Introduction With the use of absorption of light a spectrophotometer sends UV wavelengths through solutions to determine their concentrations. The light absorbed is measured as the atoms‚ molecules and ions absorb the wavelengths of light that the spectrophotometer gives off (Meah‚2013). The level of light transmitted defines the amount of light absorbed‚ for instance‚ the lower
Premium Electromagnetic radiation Concentration Chemistry
Movement Cardiovascular Dynamics Laboratory Report Student ID 2010004614 Due date and Value: This report must be submitted as a soft copy via email to abarnett@hku.hk no later than 5:00 pm 4 April 2012. Penalties apply for late submission‚ see course outline for details. You must attend the laboratory session to get a mark for the related report. References used when answering questions must appear in a reference list at the end of your report. Value: This report contributes 10% of your final
Premium Blood pressure
Measurement of stiffness of rock from laboratory and field tests Naeem O. Abdulhadi & Amjad F. Barghouthi Arab Center for Engineering Studies (ACES) ABSTRACT This paper compares the deformation modulus of rock measured from laboratory and field tests which were carried out as part of the site investigation works for a major project in Irbid‚ Jordan. Laboratory resonant column and torsional shear tests were performed at different confining pressures whereas ultrasonic velocity tests were
Premium Elasticity Compressive strength
| Date:2/11/13 | Exp 1: Laboratory Techniques & Measurements | Lab Section: 73426/0 | Data Tables: Length and Measurements Object Measured | Length in cm | Length in mm | Key | 6.4cm | 64mm | Fork | 26.5cm | 265mm | CD | 17cm | 170mm | Warm Temperature Measurements Hot tap water temperature _73___˚C Boiling water temperature _101___˚C Cold Temperature Measurements Cold tap water temperature __15__˚C Ice water temperature __0__˚C Volume Measurements Volume of completely filled
Premium Temperature Measurement Units of measurement
PERTH COLLEGE UHI 12 INSTRUMENTATION OF A WIND TUNNEL PROJECT BEng(Hons) Gaurab Ghosal ABSTRACT The wind tunnel being built in Scone airport is a closed loop wind tunnel. On completion this will provide a much needed facility for education purpose as it can be used by engineering students for aerodynamic evaluations. To conduct these evaluation proper evaluating tools needs to be setup. In this section the possible instruments that can be setup in this wind tunnel has been evaluated with
Free Fluid dynamics Aerodynamics
1. Summary In this internship‚ my company of attachment is Chevron Singapore‚ Laboratory (Lubricants Department)‚ as a Lab Analyst intern. As an intern‚ my duties are to do lab testing‚ as well as relevant paperwork involving Statistical Quality Control testing. Additionally‚ as shift work is a requirement for Lab Analysts‚ I will be helping the Analyst I am attached to for shift work in some tests such as the Analysis of Metals via Inductively Coupled Plasma Atomic Emission Spectrometry‚ and Density
Premium Chevron Corporation Chevron Corporation Texaco
Materials and Method In order to complete this experiment we used a combination of electrocalorimeter (immersion heater and calorimeter)‚ power supply‚ ammeter (0 to 3 A)‚ voltmeter (30 V)‚ rheostat‚ connecting wires‚ thermometer‚ stopwatch‚ laboratory balance‚ and ice. In order to obtain the data‚ the DataStudio™ software is set up on the computer to use the temperature sensor on the apparatus to collect steadily the temperatures at specified time interval of 5-seconds. After the computer is
Premium Heat Thermodynamics Energy
CALIBRATION OF TEMPERATURE AND PRESSURE SENSORS Mechanical Engineering Department Loyola Marymount University Los Angeles‚ California ABSTRACT In this laboratory experiment‚ an Omega Model PX- 236-060GV piezoresistive pressure transducer was calibrated‚ by using an AMTEK model deadweight pressure tester. For the temperature calibration an Jofra Model C-140 temperature calibrator was used. The experiment began by setting up the Jofra Model C-140 temperature calibrator‚ and taking data from
Premium Measurement Metrology
Experiment 2: Laboratory Techniques and Measurements Course Number: CHE 111 Abstract: This experiment introduced the student to lab techniques and measurements. It started with measuring length. An example of this would be the length of a nickel‚ which is 2cm. The next part of the experiment was measuring temperature. I found that water boils around 95ºC at 6600ft. Ice also has a significant effect on the temperature of water from the tap. Ice dropped the temperature about 15ºC. Volumetric
Premium