oil grade | : | SAE 10 | Valve Clearance Cold - Inlet | : | 0.10 - 0.15 mm | Valve Clearance Cold - Exhaust | : | 0.15 - 0.20 mm | Cooling System (litres) | : | 1.9 | Tyre Pressure Front Bar / psi | : | 28 | Tyre Pressure Back Bar / psi | : | 33 | Tyre Pressure Back - Pillion Bar / psi | : | 36 | Engine Oil Grade SAE | : | 10W/40 | Engine Oil Classification API | : | SE/SF | Engine Oil quantity with filter (litres) | : | 2.8 | Chain Freeplay mm | : | 25 - 35 | Idle Speed (rpm)
Premium Internal combustion engine
PSI India – Will Balbir Pasha Help Fight AIDS? Submitted By: Soumyo Pattnaik (U109115) Problem The case presents a problem over choosing a suitable mass campaign route to be taken by an NGO named Population Services International (PSI)‚ India. Their aim is to raise awareness about HIV/AIDS among the vulnerable groups due to lifestyle behavior. They wanted to design a differentiated campaign to connect with the target population at a wider and deeper level. 1. Do you think it is wise for
Premium HIV Condom Sexual intercourse
steel rod with a cross-sectional area of 0.25 in2 is stretched between two fixed points. The tensile load at 70°F is 1200 lb. What will be the stress at 0°F? At what temperature will the stress be zero? Assume α = 6.5 × 10-6 in/(in·°F) and E = 29 × 106 psi. Solution 261 For the stress at 0°C: answer For the temperature that causes zero stress: answer problem 262 A steel rod is stretched between two rigid walls and carries a tensile load of 5000 N at 20°C. If the allowable stress
Premium Tensile strength Atmosphere
PRESSURE MEASUREMENT AND CALIBRATION YEDĐTEPE UNIVERSITY DEPARTMENT OF MECHANICAL ENGINEERING 1 YEDITEPE UNIVERSITY ENGINEERING FACULTY MECHANICAL ENGINEERING LABORATORY Pressure Measurement and Calibration 1. Objective: To convert an arbitrary scale of pressure sensor output into engineering units. To calibrate a semiconductor pressure sensor. 2. Equipment: The equipment comprises a Dead-weight Pressure Calibrator (DPC)‚ Bourdon gauge and diaphragm-type pressure sensor. The
Premium Pressure Atmospheric pressure
SPE 167543 Wellbore Stability Management In Depleted And Low Pressure Reservoirs Fekete Paul O.‚ Dosunmu Adewale‚ Anthony Kuerunwa‚ Ekeinde Evelyn B.‚ Anyanwu Chimaroke‚ and Odagme Baridor S.‚ Dept. of Petroleum and Gas Engineering‚ University of Port Harcourt‚ Nigeria Copyright 2013‚ Society of Petroleum Engineers This paper was prepared for presentation at the Nigeria Annual International Conference and Exhibition held in Lagos‚ Nigeria‚ 30 July–1 August 2013. This paper was selected for presentation
Premium Particle size distribution Calcium carbonate
Powder metallurgy is the process of blending fine powdered materials‚ pressing them into a desired shape or form (compacting)‚ and then heating the compressed material in a controlled atmosphere to bond the material (sintering). The powder metallurgy process generally consists of four basic steps: (1) powder manufacture‚ (2) powder blending‚(3) compacting‚ (4) sintering. Compacting is generally performed at room temperature‚ and the elevated-temperature process of sintering is usually conducted at
Premium
is classified as a research university with high research activity by the Carnegie Foundation and a first-tier research university by the Florida Legislature. Founded in 1965‚ FIU is the youngest university to be awarded a Phi Beta Kappa chapter by the Phi Beta Kappa Society‚ the country’s oldest academic honor society. FIU belongs to the 12-campus State University System of Florida and is one of Florida’s primary graduate research
Premium University Florida College
The letter K comes from the letter Κ (kappa)‚ which was taken from the Semitic kap‚ the symbol for an open hand.[2] This‚ in turn‚ was likely adapted by Semites who had lived in Egypt from the hieroglyph for "hand" representing D in the Egyptian word for hand‚ d-r-t. The Semites evidently assigned it the sound value /k/ instead‚ because their word for hand started with that sound.[3] In modern-day English slang‚ the word "k" is used as a substitute for the abbreviation "O.K."‚ or "Okay." In International
Premium English language Greek alphabet Linguistics
Your forms may be completed online from any trusted computer with internet access including your home system. If at any point you require assistance‚ please call the PSI-CoE Call Center at 410-278-4194 or DSN 298-4194. Once you complete and release your forms to the PSI-CoE for review‚ you should expect to receive email notices from the PSI-CoE’s office account psip@conus.army.mil. If any errors are detected you will be notified via email that your forms have been returned to you for correction. Please
Premium Error Completeness
PPI TN-27/2009 Frequently Asked Questions HDPE Pipe for Water Distribution and Transmission Applications PPI TN-27: Frequently Asked Questions HDPE Pipe for Water Distribution and Transmission Applications Foreword This report was developed and published with the technical help and financial support of the members of the PPI (Plastics Pipe Institute‚ Inc.). The members have shown their interest in quality products by assisting independent standards-making and user organizations in the development
Premium Pressure Water Plumbing