Compound Microscope Parts A high power or compound microscope achieves higher levels of magnification than a stereo or low power microscope. It is used to view smaller specimens such as cell structures which cannot be seen at lower levels of magnification. Essentially‚ a compound microscope consists of structural and optical components. However‚ within these two basic systems‚ there are some essential components that every microscopist should know and understand. These key microscope parts are illustrated
Premium Cell cycle Cell Bacteria
Nervous System lab was designed to measure reaction times by using a variety of tests that affect the heart rate. These tests were the startle‚ stroop‚ Valsalva maneuver‚ diving reflex‚ and a test of our choice. The test our group chose to measure the heart rate in response to doing a trust fall to anticipate the stress right before the fall. To begin this lab we chose a participant‚ and then hooked their finger up to the pulse transducer sensor. Using the chart 5 program on the lab computer the participant’s
Premium Parasympathetic nervous system Autonomic nervous system Peripheral nervous system
department Data security – Lab # 1 Lab Description Set-UID is an important security mechanism in Unix operating systems. When a Set-UID program is run‚ it assumes the owner’s privileges. For example‚ if the program’s owner is root‚ then when anyone runs this program‚ the program gains the root’s privileges during its execution. Set-UID allows us to do many interesting things‚ but unfortunately‚ it is also the culprit of many bad things. Therefore‚ the objective of this lab is two-fold: • Appreciate
Premium Computer Personal computer Computer program
second part of the experiment‚ we determined that varying the materials between two sliding surfaces changesthe coefficient of kinetic friction between them. Finally‚ in both parts‚ we showed that friction depends on the normal force. OBJECTIVES 1. To determine the coefficient of friction μ between contact surfaces as one body moves uniform motion. 2. To establish the relationship between angle of repose ∅ and μ METHODOLOGY Determination of the coefficient of Friction. - Place the
Premium Friction Force Classical mechanics
Lab report As part of my module Nip1002 I was required to perform a set of observational skills which included; pulse‚ blood pressure‚ respirations‚ hand washing and urinalysis and then compare them to previous results. In this lab report I am going to discuss blood pressure in detail. Procedure * Explain the procedure to the patient and gain consent * Wash hands thoroughly following the hand wash technique to prevent the transfer of bacteria * Clean equipment e.g. blood pressure cuff
Premium Blood pressure
Lab #4: The Immune System Purpose: The purpose of this lab was to perform and understand the procedures of conducting an ELISA test to determine whether a particular antibody is present in a patient’s blood sample through a virtual simulation. Hypothesis: If I successfully complete this lab‚ I will then understand how to perform an ELISA test‚ the purpose an ELISA test‚ and also how to interpret the results of this test. Materials and Procedures: Materials: Howard Huges medical
Premium Antibody Immune system Immunology
Lab #1 Submission 1. Name at least five applications and tools pre-loaded on the TargetWindows01 server desktop‚ and identify whether that application starts as a service on the system or must be run manually. Wireshark – manual Nessus Client – manual Nessus Server Manager – can be set up to run at Startup Filezilla Server Interface – starts as a service Zenmap GUI - manual 2. What was the allocated source IP host address for the TargetWindows01 server‚ TargetUbuntu01 server‚ and the
Free Linux Subnetwork Internet Protocol
Nb+Ma+Va=Na+MbVb ‚ the molarity is able to be determined. Procedure: 1) Using the graduated cylinder add 10.0 mL of water into the Erlenmeyer flask. 2) Add 5.0 mL of HCl into the flask using another graduated cylinder because acid goes into water when mixing them. 3) Add three drops of phenolphthalein indicator into the flask. 4) Swirl the flask in circular movements to mix the substances. 5) Put the flask under the buret of NaOH solution‚ make sure the buret’s tip is inside the flask’s
Premium Titration Sodium hydroxide Acid
Sample Short Lab Report By Charles M Borener Jr April 24‚ 2009 Kinetic Friction Experiment #13 Joe Solution E00123456 Partner - Jane Answers PHY 221 Lab Instructor – Chuck Borener Thursday‚ 11 AM – 1 PM Lecture Instructor – Dr. Jacobs Abstract In this experiment‚ we test factors which effect friction. We pulled a wood block across a surface to determine whether the surface area of the block or the type of surface effects friction. We found that the surface area of the block did not change
Free Force Friction Mass
Joe Schmoe Period 3 March 8‚ 2013 Lab Report: Empirical Formula of Zinc Chloride (ZnCl) * Purpose The purpose of this experiment was to learn how to determine the empirical formula. Empirical means “based on experimental evidence.” * Experimental Design The reaction that occurred was the reaction of the elements Zinc (Zn) and Chloride (Cl) by mixing a piece(s) of Zinc and 50mL of Hydrochloric Acid (HCl). The amount of Zinc was determined to be between 1.00g and 1.25g. As the reaction
Premium Hydrochloric acid Chlorine Hydrogen