Lab 19A Answers: 1) If we increase the molarity of NaOH from 0.1M to 0.2M‚ it will actually take less number of drops in order to change the color of the solution. This is because the more concentrated a substance is‚ less of the substance is needed to cause an equilibrium shift. 2) When you add 6.0M NaOH into the iron (III) thiocyanate ion equilibrium system‚ the concentration of Fe3+ ion decreases. This causes the equilibrium system to shift to the left (reactant) side. This is why the solution
Premium Sodium Sodium chloride Ion
Chemistry 12 - Lab 19A Flow Chart (Investigating Chemical Equilibrium) PART 1: Put on safety goggles and lab apron Obtain 2 (Empty‚ Clean‚ AND DRY) 250mL Erlenmeyer flasks. Add approx. 100mL of DISTILLED water and 1mL of thymol blue solution to each flask Record the colour of this solution in note book FIRST FLASK: add a single drop of 0.1M HCl. Swirl the contents of the flask and continue drop-by-drop addition until a definite colour change is observed. SECOND FLASK: will serve as
Premium Red Color Chemical reaction
Chemistry 121 Colligative Properties Lab Demonstration of Selected Calculations from Choice I Determination of Kf for Naphthalene To determine the Kf for naphthalene‚ we need to find the difference in the freezing point of pure naphthalene and the solution of 1‚4-dichlorobenzene in naphthalene. Let’s say that we did this experiment‚ used 1.00 g 1‚4-dichlorobenzene in 10.00 g naphthalene‚ and found that the freezing temperature of pure naphthalene was 78.2°C‚ while that of the solution was 75
Premium Chemistry Atom Oxygen
The purpose of this lab was to see which solutions are soluble and which are not. We were able to see this by mixing certain solutions together and observing changes that occurred. The procedure for this experiment included a few different steps. The first steps were to add the nitrate solutions into the lettered parts of the 96-well plate. Once you were done with that‚ you were supposed to add the sodium solutions to the numbered parts of the 96-well plate‚ so that the solutions were added together
Premium Ion Solubility Chemistry
ATLANTIC COLLEGE CHEMISTRY DEPARTMENT (Written by Dr Geoffrey Neuss) CONTENTS Page Introduction 1 Assessment of Practical Work 3 Error and uncertainty 7 Significant figures 8 Title 1. Some common chemical reactions. 9 2. A traditional acid-alkali titration. 10 3. Analysis of aspirin tablets
Premium Titration Chemistry Assessment
to observe a shift in equilibrium concentrations associated with changes in temperature 4. to explain the observations obtained by applying Le Chatelier’s principle Materials Required: See page 209 Heath Chemistry Laboratory Experiments Procedure: See pages 209-211 Heath Chemistry Laboratory Experiments Data and Observations: Table 1 Equilibrium Involving Thymol Blue REAGENT ADDED STRESS (ION ADDED) COLOR OBSERVATION DIRECTION OF EQUILIBRIUM SHIFT HCl (Step
Premium Chemistry Experiment Hypothesis
October 13‚ 2012 Needle through a Balloon Pre-Lab Preparations: Purpose: The purpose of this experiment is to see if the balloon pops when pierced with a wooden skewer or a sharp pin. Hypothesis: If we lubricate the skewer with petroleum jelly‚ then it should go through the balloon without popping. Hypothesis for the 2nd part of the Lab: If we cover the side of the balloon with cellophane tape‚ then it will not pop when pierced with the pin. Materials: • Balloons • Long wooden
Premium Hypothesis Observation Stanford prison experiment
Jashandeep Gill Gammellos Chemistry Density is one of the fundamental principles of physics. Density is the reason why a plank of wood floats on water while a piece of metal several times smaller will sink. Density of an object is measured in g/cm³ or g/cc. The equation is D=M/V‚ D being the density of the object‚ M being the mass of the object‚ and V being the volume of the object. Mass is the space an object takes up. It is the amount of matter present in an object. Mass is measured using
Free Density Water Kilogram
Procedure Access the virtual lab and complete the experiments. Part One (Flame Test): 1. Create and complete a data table for Part One of the lab. It should include the name of the element (or unknown) examined and the color of the observed flame: Barium-green Calcium-red Sodium-yellow Rubidium-purple Potassium-blue Lithium-pink 2. Identify each unknown from Part One of the lab and briefly explain why you identified each unknown as you did.: Unknown 1-yellow. I think it is Sodium because
Premium Light Atom Color
Physical and Chemical Change Objective: Recognize and distinguish between chemical and physical changes. Materials: - lab balance - microspatula - lab burner - dropper pipet - 5 test tubes - mortar and pestle - test tube rack - magnet - test tube holder - insulating pad - watch glass - safety goggles - glass square - lab apron or coat - copper sulfate pentahydrate - iron fillings - sodium chloride - magnesium ribbon - hydrochloric acid - paper
Premium Chlorine Mixture Sulfuric acid