iLab5A /* Specification: lsd Lab 5 Exercise A This program takes input from the user taking player names (up to 100) and player scores (up to 100). When the user enters Q to quit the program a summary is displayed with all the player names‚ player scores‚ the average score‚ then a list of players who scored below the average. */ using System; using System.Collections.Generic; using System.Linq; using System.Text; namespace LAB5 {
Premium Scores The Score The Players
Lab 6.1 Standard Frequency (GHz) Max Transmission Rate (Mbps) Standard Indoor Transmission Range (m) Standard Outdoor Transmission Range (m) 802.11a 5 54 35 120 802.11b 2.4 11 38 140 802.11g 2.4 54 38 140 802.11n 2.4.5 600 70 250 Lab 6.2 Lab 6.3 Mine spoke with all at a 100% ratio Lab 6.4 The AP placement in a home or office would be affected depending upon home layout and network setup (device placement) as well as trying to keep others from accessing your network from outside the home. The
Premium Wi-Fi
appliance (template) or create VM with ISO. 3. Add both the network interfaces to the VM. 4. Login with username: vyatta and password vyatta. 5. If created through ISO‚ run “install system” command on the console and install it to the server hard drive. Vyatta Configuration. I. Adding interfaces Add both the interfaces in the router with specific address. Type “configure” and enter (for entering configure mode). Type the following commands Set interfaces ethernet eth0 address <External
Premium IP address
Lab 5: Ethernet LANS Exercise 5.1.1 The IEEE standards cover more than just Ethernet. The 802.3 standard actually builds upon the 802.1 network architecture standard from IEEE. Briefly define the 802.1 standard and what it provides. Use your textbook and the Internet to research your answer. A: The 802.1 standards provide LAN/MAN management. The 802.1 standards where created by the close of the 1970’s. Exercise 5.1.2 The 802.3 family of standards has the format 802.3x where x is a sequence of letters
Premium Ethernet
Abstract The objective of this lab was to determine the convective heat transfer coefficient of a heated sphere in an quiescent environment. In the experiment a hot brass sphere was put into water and cooled. The temperature of the sphere was recorded over a time of 600 seconds to see how it cooled and given temperature was recorded every 20 seconds. Results were then calculated at both of the time values 300 and 600 seconds. For the experimental results at time 300 seconds‚ the Rayleigh number
Premium Convection Heat transfer Heat
Amanda Jornd Experiment 7- Synthesis and Reactivity of tert-Butyl Chloride Via an SN1 Reaction Introduction/Background: Alkyl halides are compounds in which a halogen atom replaces a hydrogen atom of an alkane. Alkyl halides are classified as primary‚ secondary or tertiary depending on the number of alkyl substituents directly attached to the carbon attached to the halogen atom. The purpose of this lab was to properly prepare t-butyl chloride from t-butyl-alcohol in a concentrated hydrochloric
Premium Solvent Hydrochloric acid
Lab 7 IS3445 Security Strategies for Web Applications and Social Networking Lab 7 Assessment 1. How does Skipfish categorize findings in the scan report? As high risk flaws‚ medium risk flaws‚ and low issue scans 2. Which tool used in the lab is considered a static analysis tool? Explain what is referred to by static code analysis. RATS‚ because the running of static code analysis tools that attempt to highlight possible vulnerabilities within ‘static’ (non-running) source code. 3. What possible
Premium Software testing Source code Internet
Note: Use 2811 series to all routers and 2960 to all switches Topology Diagram Learning Objectives Upon completion of this lab‚ you will be able to: • Cable a network according to the Topology Diagram. • Erase the startup configuration and reload a router to the default state. • Perform basic configuration tasks on a router. • Configure and activate Serial and Ethernet
Premium IP address Subnetwork Routing
5. (10 pts) Consider the network shown below. Suppose AS3 and AS2 are running OSPF for their intra-AS routing protocol. Suppose AS1 and AS4 are running RIP for their intra-AS routing protocol. Suppose eBGP and iBGP are used for the inter-AS routing protocol. Initially‚ suppose there is no physical link between AS2 and AS4. * Router 3c learns about subnet with prefix x from which routing protocol: OSPF‚ RIP‚ eBGP‚ or iBGP? eBGP * Router 1d learns about subnet with prefix x from which routing
Premium Routing Border Gateway Protocol Router
CNC ROUTER Model XJ-2040 Working area 2‚000×4‚000×200mm Spindle motor 3kw/4kw/4.5kw Inverter-driven spindle motor cooled by water (or air for option) Working mode Stepper motor Control system DSP off-line control panel with USB interface(128MB) or PCIMC control system Drive mechanism Gear-wheel on x‚y axis Table surface Vacuum table and T-slot extrusions Frame Wholly steel structure Motion positioning accuracy ± 0.03/300mm Repositioning accuracy ± 0.05mm Max motion speed 50
Premium Wood