Lab Report Experiment 1 & 2 CHM-101 Amele Takpara Partner: Jessamyn Dupree ------------------------------------------------- Experiment 1 ------------------------------------------------- (Pre-Lab Questions) 1. In the design of a Bunsen burner‚ explain the purpose of a. the gas control valve The gas control valve regulates the rate at which methane enters the burner. b. and the air vents. The air vents control the rate at which air enters the burner 2. Why is a luminous
Premium Temperature Volume Liquid
responsible for making the pillbug habitat‚ taking them in and out of the habitat for our experiment‚ setting up the experiment setups for testing‚ and timing the experiment. In my opinion‚ I contributed a lot in my group. I did a majority of the lab proposal‚ and a substantial amount in the lab report. I was always the one getting up to gather our materials and pillbugs from the bins and making sure that our experiment was going as smoothly as intended. From this project‚
Premium Scientific method Project management Management
Objective: The purpose of this lab is to demonstrate that there is a linear relationship between the number of molecules that can absorb light present in a solution and the amount of light absorbed by a solution. This lab should prove that Beer’s law and the equation A=a x b x c‚ is a linear relationship. Procedure: The only deviations in the lab procedure was that the stock solution was made before arrival to the lab with 0.570 g of KMnO4 in 0.500 L. The diluted solutions and the
Premium Concentration Mole
Osmosis Experiment Dennis M. Feliciano Grand Canyon University BIO100L Biology Concepts Lab June 25‚ 2011 Osmosis Experiment Materials Grapes (unblemished) Raisins (larger is better) Water Salt Four small containers (i.e.‚ drinking cups or clear glasses) A metric ruler Methods and Procedure Place 1 cup (236 ml) of water in each of the 4 containers. In 2 of the containers‚ add 1 tablespoon (14.8 ml) of table salt and mix well. Measure the length and width of a raisin and place
Premium Osmosis Chemistry Concentration
Extended Experimental Investigation | May 28 2013 | Drosophila melanogaster lab experiment Question: How do the dominant or recessive genes in particular traits in a cross between a male and female Drosophila determine the traits of its offspring? Aim: to establish whether characteristics produced from the offspring of a drosophila cross are recessive or dominant traits. Hypothesis: If certain phenotypes are expressed in the offspring from the cross of certain Drosophila‚ then the determination
Premium Allele Zygosity Dominance
Taha Al-Yousif Hooke’s Law Lab Date conducted: September 18th 2013 Partners: Mohammed‚ Liam‚ Ben Nguyen Purpose: The purpose of this experiment is to find the relationship between the stretch of the spring and the attached mass and to verify that this relationship is accurately described by Hook’s Law. Theory: Hooke’s Law states that to extend a spring by an amount (Stretch) from its previous position‚ one needs to add an external force (Mass). Therefore
Premium Mass Elasticity Force
It would be nearly impossible to have the transportation of vesicles without kinesin to guide it. And without the transportation of these synaptic vesicles to release their neurotransmitters‚ there would be no movement in the cell at all. This experiment is so important because vesicle transport in neurons helps to identify many neurological disorders. One such example is a research on Drosophila. Since there is only one kinesin light gene in the subject‚ the mutants in that one chain gene exhibit
Premium Nervous system Neuron Protein
Gas Laws Lab Introduction: The four basic physical properties of a gas sample are pressure‚ volume‚ temperature‚ and number of moles. The volume simply indicates the volume of the container since a gas will take up all space available to it. The temperature indicates the average kinetic energy of the gas particles. For gases‚ the temperature must be converted to the Kelvin unit. The pressure of the gas indicates the number of collisions with each other and the wall of the container. The number
Premium Gas Pressure Ideal gas law
Experiment AM1.4--Bending moments in a simply supported beam Student name JunJie Liu Student ID 1512042 Experiment Date 24 Nov 2014 Lab group Mech 7 Introduction In this lab report we show the basic methods of measuring bending moment at the “cut” assuming only simply supported beam with point loads (showed in figure 1) and illustrate the relationship among bending moment and distance between
Premium Force Torque Experiment
Surface Tension Steven Brignol Dr. Payne September 15 Introduction: Water’s ability to stick to itself is surface tension. In this lab we were able to measure and detect surface tension by dropping water‚ drop by drop‚ onto a penny. The quantity of droplets that fit on the penny was impressive. Hypothesis: The detergent will thicken the water making a tighter surface tension. Prediction: If soap increased the surface tension‚ then expansion will happen. Materials: (1) Pipette (2) Water
Premium Liquid Experiment