Raquel Johnson October 19‚ 2014 Solids: Recrystallization and Melting Points Organic Chemistry 2423 Lab Report: Recrystallization Abstract: The purpose of this lab was to purify an unknown compound by recrystallization. Taking an unknown compound and identifying it by purifying it from its impurities through the use of hot gravity filtration. Then to determine the unknown you were to take the melting point. An unknown compound was recrystallized from hot water to produce 0.99 grams (67% recovery)
Premium Temperature Solubility Solid
The machine was unplugged. * Using a ruler‚ a pencil and the Ticker Tape‚ all the data were recorded on a Data Table. * Using the Data Table the position versus time graph and the velocity (instantaneous) versus time graph were plotted. Analysis There were in total of 37 dots recorded on the piece of the Ticker Tape. Every sixth dots represented the 1/60th of one second. Because of the lack of the information‚ as shown on the Data Table‚ every third dots were used to expand the amount
Premium Acceleration Kinematics Velocity
In 1860‚ the first instrumental analysis was performed by Robert Bunsen and Gustav Kirchoff who used flames tests that led to the discovery of the elements rubidium (Rb) and caesium (Cs). After this‚ this method was used everywhere to find the chemical make ups of many substances. For example‚ in 2007 there was a huge problem where tainted pet food would cause many pets to become ill. Qualitative analysis was used and it was discovered that Melamine was found in the pet food which altered the results
Premium Chemistry Hydrogen Water
Introduction and Purpose: This lab focuses on how weight affects the time it takes for a rotocopter to fall from a drop height of 1 and 2 meter(s) respectively. The primary goal of this lab is to investigate and explain the relationship of these two factors. During the process of conducting this experiment‚ learning to design a lab will also be achieved. Research Question: What is the effect of weight on the time it takes for a rotocopter to fall from a drop height of 1 and 2 meter(s)? Variable
Premium Force Classical mechanics Mass
was higher than the actual melting point of pure aspirin; 135°C. The phenol test showed that the product is not a pure aspirin by expressing purple color. TLC results weren’t high enough to conclude that the product was a pure aspirin. Overall‚ the lab wasn’t successful due to the low percentage of aspirin that were produced. Out of 2.0 grams of aspirin‚ only 0.7862 grams of pure aspirin were produced. So the percent yield was only 39%. Errors could be made during filtration process and the melting
Premium Chemistry Acetic acid Water
Impurity Lab Report Aim: To find out the difference of the boiling point and melting point when adding impurity (salt) to water. Diagram: Method: 1.Set up the apparatus as shown in the diagram 2. Get a known amount of ice in the beaker (half full)‚ and a known amount of salt in another beaker 3. Measure the temperature (melting point) of the ice without adding any impurity (salt). 4. Measure the temperature (melting point) of the ice after adding the salt into the beaker. 5. Heat up
Premium Water Solid Fahrenheit
Lab Report Procedure 6.1: Perform Benedict’s test for reducing sugars. Introduction: Benedict’s tests allows for the detection of the presence of reducing sugars. All monosaccharides are reducing sugars since all of them have active carbonyl group. Some disaccharides that are exposed to a carbonyl group are also reducing sugars but less reactive than monosaccharides. By mixing the sugar solution with Benedict’s solution and heating them‚ a redox reaction will occur. The copper (II) sulphate
Free Glucose Carbohydrate Sucrose
Lab Report Density Name: Period: Problem How do you calculate Density? What units did you use for volume‚ mass‚ and density? When the cubes are placed in water which one will sink 1st? What is the ranking of the cubes lightest (1) to heaviest (10)? Is it true that the cube with the most mass will have the most density? Hypothesis I think the 1st cube was aluminum I think the 2nd cube was steel I think the 3rd cube was brass I think the 4th cube was copper I think the 5th
Premium Density Volume
This lab experiment investigates the effect of listening to different types of music on one’s pulse. The experiment relates the circulatory system to the pulse as it measures how quickly the heart contracts and releases blood. Pulse is measured in beats per minute (bpm). One’s pulse is loudest near the heart‚ because there is more pressure closer to the heart. In contrast‚ one’s pulse is quieter the further away it is measured from the heart‚ because there is less pressure the further the distance
Premium Heart Psychology Experiment
chemistry lab report : reaction of alcohol CHEMISTRY LAB REPORT SK026 SEMESTER 2 SESSION 2011/2012 TITLE :REACTION OF ALCOHOL DATE : NAME : MATRIC NO : PARTNER : PRACTICUM : SUPERVISOR : Title : Reaction Of Alcohol Objectives : 1. To classify alcohol 2. To study the chemical properties of alcohols Introduction: Alcohol is a class of organic compound containing hydroxyl group‚ OH as the
Premium Alcohol Ethanol Carboxylic acid