experiment was to investigate the effects of salt type and concentrations on the rate of heating and the boiling point. Then from this data make a conclusion which salt type and concentration is the most energy efficient at heating water to its boiling point. It was hypothesised that highest concentration of MgCl2 was going to be the most energy efficient at heating the solution to its boiling point. This is because MgCl2 has the lowest specific heat capacity thus will use the least amount of energy
Premium Water Heat Chemistry
Emilia Monroe August 27‚ 2014 Experiment #01 The Determination of the Percent of Water in a Compound CHEM 1315-022 For experiment one‚ The Determination of the Percent of Water in a Compound‚ the sole purpose of conducting this experiment was to determine the percent of water found in compounds such as Magnesium Sulfate‚ Copper Sulfate‚ and so on. Along with determining the percentages of the hygroscopic compounds the experiment allowed for the exploration of separation of hydrogen bonds
Premium Chemistry Water Oxygen
2.4.4. Direct determination of saliva proteins Protein contaminated with nucleic acids absorbed the light at wavelength 280 nm and it absorbs much strongly at wavelength 205 nm when it is free from nucleic acids. The UV-visible spectrophotometer was used in determination of saliva proteins (Figure 2.2). Cold trichloroacetic acid (10 % w/v ) was added to the sample‚ centrifuged for 10 minutes to precipitate protein. The absorbance of a known volume
Premium Protein Gel electrophoresis Enzyme
Point load test Aim: To determine the strength characteristics of a rock using the point load test and visual judgement. Materials Loading device Loading frame Pump Ram Platens Rock Caliper Method (Standard‚ 2007) 1. Measure the dimensions of the rock which includes the diameter and length 2. Find the length to diameter ratio to determine which test will be used. If the ratio is greater than 1 use diametrical test. But if the ratio is between 0.6 and 1 use axial test 3. The axial
Premium Geology Mineral
The experimental melting point range of the desired alkene product‚ trans-9-(2-phenylethenyl) anthracene‚ was found to be 132-134 ˚C‚ in comparison to the literature value melting point range of 130-132˚C‚1 it was slightly higher than expected. Overall‚ the experimental melting point range varied from the initial melting point temperature and maximum melting point temperature by 2˚C. As the experimental melting point had a small range of temperature variance and was above that of the literature value
Premium Melting point Temperature Liquid
Gravimetric determination of sulphate in fertiliser Question: The proportion of sulphate present in a brand of commercial fertiliser under a range of temperatures. Fertilisers provide plants with a number of sources necessary for them to grow‚ as follows‚ nitrogen‚ phosphorus‚ potassium and finally the one I will be concentrating on Sulfur. To cater for the varying plants‚ you wouldn’t require all these elements to the same extent as the necessities for each plant differ. The composition of different
Premium Oxygen Chemistry Enzyme
Melting Point Determination and Thermometer Calibration Lab Background: The melting point of a substance‚ a solid in this case‚ signifies the temperature at which the first crystal starts to melt until the temperature at which the last crystal disappears is reached. That being said‚ melting points are expressed in ranges‚ am organic compound will have a sharp range depending on the purity of the compound. Impurity of an organic substance will register an abnormal melting point based on its
Premium Salicylic acid Temperature Chemical compound
Report of Density Determinations Density is defined as the mass of substance per unit volume. Both pure substances and solutions are applicable. Today we are going to determine the Density of rock chunks and NaCl solution. In this experiment‚ we will determine the mass and volume of each object and then we will calculate the ratio—the density. In the first part of the experiment‚ we should measure the density of some irregularly shaped chunks of rock. The Weight of rocks is 18.769g
Premium Sodium chloride Volume Liquid
D. F. Nachman Thermochemistry: An Ice Calorimeter Determination of Reaction Enthalpy 9/11/2014 Introduction: A chemical reaction often indicated by a transfer of energy measured in heat. By measuring this heat transfer in a constant pressurized environment‚ the enthalpy of the reaction can be used to infer certain information about a specific reactions reactants and products. The transfer of heat from outside sources in would be described as an endothermic reaction. Contrary‚ when
Premium Thermodynamics Energy Enthalpy
Title of the Experiment: determination of densities Introduction The density of a sample of matter represents the mass contained within a unit volume of space in the sample. For most samples‚ a unit volume means 1.0 ml. The units of density‚ therefore‚ are quoted in terms of grams per milliliter (g/ml) or grams per cubic centimeter (g/cm3) for most solid and liquid samples of matter. Density is often used as a point of identification in the determination of an unknown substance. The density
Premium Density Volume Temperature