listed below. You must observe and analyze these as part of the lab. The Iced Tea Debate The Salty Soup The Fire Bug 2 Use the DATA chart provided for recording observation based on three demonstrations you will watch 3 Watch each part of the experimental demonstration and make preditions about wht will happen in each scenario . Record your preditions and observations in the Data an Observations section of your labatory report format. Problem: How can matter and energy be described in
Premium Energy Conservation of energy Chemistry
CE121: Construction Materials Laboratory Report No. 1 Particle Size Distribution Van Joseph E. Casalme 2010-14928‚ BS Civil Engineering Institute of Civil Engineering‚ College of Engineering University of the Philippines Diliman‚ Diliman Quezon City 1101 Submitted to: Engr. Christian R. Orozco ABSTRACT This test (ASTM C136-06) determines the grading of materials being used as aggregates using two parameters (coefficient of uniformity and gradation) from particle-size distribution
Premium Sieve analysis Particle size distribution Construction aggregate
Solute Concentration of Potatoes Lab #1 Purpose: To find the molarity/concentration of potato cytoplasm. Materials: As on page 1 in the lab handout. Procedure: As on page 1 in the lab handout. Data and Observations: Test Tube # | Concentration of sucrose solution (mol/L) | Initial Mass (g) | Final Mass | Percentage change in mass | 1 | 1.0 mol/L | 3.00g | 2.25g | -25.0% | 2 | 0.9 mol/L | 2.70g | 2.07g | -23.3% | 3 | 0.8 mol/L | 2.92g | 2.25g | -22.9% | 4 | 0.7 mol/L | 2.60g
Premium Concentration Osmosis Chemistry
Acid Base Titration Purpose: The purpose is to calculate the molarity of a NaOH solution by titrating the base with 5mL of standard HCl solution in each trial. By adding the base with unknown molarity to the acid with 0.10M the molarity of NaOH can be calculated. The base‚ NaOH‚ helps bring the pH of the acid‚ HCl‚ closer to seven‚ which neutralizes it. When using the buret the amount of NaOH used is able to be determined. Then by writing a balanced chemical equation and using the titration
Premium Titration Sodium hydroxide Acid
Bubble Inside a Bubble Materials • • • • • • • • Granulated sugar (we had our best results using Imperial Sugar and Dixie Crystals) Dish soap Water Tablespoon Scissors Pipette Cup Adult supervision Bubbles form because of a combination of water’s hydrogen bonds and the oily film you can see shimmer in the light. The oily film you see is actually two separate layers of soap attached to‚ and surrounding‚ hydrogen-bonded water. Solar Oven S’mores Materials • Pizza box • Two clear sheet protectors
Premium Oxygen Thermodynamics Water
Abstract This lab’s purpose was to test the patterns of percolation in various places. This lab tested how soil would absorb water based on different places. Distance from a group of trees‚ distance from a swamp‚ and different types of soil were tested. From the results collected‚ you can not prove‚ but you can infer that the ability to absorb increases as you go farther away from a swamp‚ and a group of trees. The ability to absorb also increases based on how much silt is in soil. Introduction
Premium Soil Surface runoff Digestion
Coulomb’s Law Purpose: The purpose of this lab was to demonstrate that the force between two stationary charges is directly proportional to the product of the charges and inversely to the square of the distance between them. Coulomb’s law tells us that the force between two charges depends (1) linearly on the strength of each charge‚ and (2) inversely on the square of the distance between them. Mathematically we would write this as . Procedures Part1 Begin by removing the right side
Premium Electric charge
# Now You See It – Copper Cycle Lab The purpose of the lab is to discover what happens when someone executes a series of procedures‚ beginning with copper metal. What is done | What is observed | 1. Started with copper‚ Cu (s). | reddish‚ brownish‚ orange-ish‚ powder-like | 2. Added nitric acid‚ HNO3 (aq). | acid turns blue and smells like chlorine. | 3. Added water‚ H2O (l). | stayed the same | 4. Added sodium hydroxide‚ NaOH (aq). | changed consistency‚ gel-like | 5. Heated the
Premium Sulfuric acid Copper Zinc
12 Reference 12 Abstract: The purpose of this experiment is to determine how a beam deflects with load and compare the experimental values to the values calculated from the simple formula and exact formula. We take three different eccentricities 75 mm‚ 55 mm‚ 35 mm and gradually apply load to them. Taking readings and making graphs to explain the outcome. This kind of experiment is helpful in construction of railways and grids
Premium Experiment Science Design of experiments
Roy Levin Bio 11 Lab Dr.Izquierdo Analysis of Macromolecules in Tissue Homogenates of Bos taurusMaterials and Methods The homogenates provided were made by homogenizing tissues in a sucrose phosphate buffer in a 1:20 ratio. The protein concentration in bovine cells was measured by diluting the homogenate with a 1:5 ratio; 50 microliters of homogenate and 200 microliters of water. Then 5 known protein concentration samples which were 0.4‚ 0.8‚ 1.2‚ 1.6‚ 2.0 mg/ml of bovine serum were used to
Premium Glycerol Glucose Liver