Calibration of Volumetric Glassware This set of laboratory experiments is designed to introduce you to some of the apparatus and operations you will be using during the remainder of this course‚ including the treatment of data using spreadsheets. While some of the procedures may seem trivial and the results obvious‚ this is a chance for you to develop good laboratory technique. Required Reading D.C. Harris‚ Quantitative Chemical Analysis (8th ed.‚ W. H. Freeman‚ NY‚ 2010) chapter 2 (Tools
Premium Mass Laboratory glassware Metrology
Rev. 01/10 JEB GLASSWARE CALIBRATION 1. Objectives Verify the actual volume of liquid delivered by 2 different types of glassware devices. Evaluate which measurement method is better for different uses. 2. Techniques Buret use: Put the buret in a buret stand and approximately fill it with temperature-equilibrated water. Make sure that the tip of the buret is filled with water and that there are no air bubbles remaining in the buret tip or valve. Record the initial level – it does not need to
Premium Water Measurement Density
LABORATORY REPORT I OBJECTIVES The objective of this experiment is to; • Identifying the range and limits of a measuring apparatus. • Rectifying any instrumental error that might be present in an instrument. • Investigating the limits and capabilities of a measuring instrument. • Determining the accuracy of the actual volume of a volumetric pipette‚ volumetric flask & measuring cylinder. INTRODUCTION The purpose of this experiment is to investigate the measurement of the actual volume
Premium Metrology Laboratory glassware Test method
EXPERIMENT 1 CALIBRATION OF VOLUMETRIC GLASSWARE OBJECTIVES 1. To calibrate a 10 mL volumetric pipette 2. To calibrate a 25mL volumetric pipette 3. To calibrate a 100mL volumetric pipette 4. To calibrate a 50mL measuring cylinder EXPERIMENTAL PROCEDURE 1) Calibration of a volumetric pipette (10mL and 25mL) (a) Pipette is used to transfer the water. If the distilled water does not drain uniformly will leaves droplets of water in the inner
Premium Mass Thermodynamics Density
Analytical Chemistry Spring 2014 September 2nd‚ 2014 Pre-Lab 1: Calibration of Volumetric Glassware Objective: The sole objective of this lab is to become acquainted with the scientific techniques that are utilized in this lab including: data analysis‚ analytical balance‚ and use of glassware and lab materials. To demonstrate these basic concepts‚ a 50 mL buret and 10 mL volumetric flask will be calibrated. Apparatus: Procedure and Equipment: The following equipment
Free Laboratory glassware Titration
Abstract: Short description of the lab and it importance. Answer three questions a. What did you do? In this experiment we were exposed to a variety of important concepts related to quantitative experimentation‚ including the proper use of glassware‚ and analytical balances. b. How did you do it? Briefly describe the procedures in 1 sentence. We calibrate a volumetric pipet and flask. We also calibrated a beaker and 50 mL buret. We also calculate the difference between the expected density
Premium Volume Density Liquid
Calibration of Volumetric Glassware Nur Farah Nabilah Binti Ahmed Zhaini Muhammad Imanuddin Bin Azman Maisarah Binti Alias Summary In this experiment‚ The purpose of this experiment is to investigate the measurement of the actual volume contents of volumetric glassware. In the beginning of the experiment‚ the volumetric glassware should be clean and dry before used. The volumetric glassware‚ measuring cylinder and pipette should be handled with care and all the precautions
Premium Measurement Laboratory glassware Density
Laboratory Experiment No. 1: Common Laboratory Procedures Objective In this experiment‚ the objectives were to use a balance and measure the volume of the liquids. Theory In the experiment‚ three calculations were used. These are the density‚ relative error and the standard deviation. Density is refers to the mass (m) per unit volume (V) of a material and is often represented by the symbols d or ρ‚ where d = m/V. The density of an object changes with pressure and temperature. Second‚
Premium Volume Density Temperature
Flinn Scientific’s Student Safety Contract PURPOSE Science is a hands-on laboratory class. You will be doing many laboratory activities which require the use of hazardous chemicals. Safety in the science classroom is the #1 priority for students‚ teachers‚ and parents. To ensure a safe science classroom‚ a list of rules has been developed and provided to you in this student safety contract. These rules must be followed at all times. Two copies of the contract are provided. One copy must
Premium Chemistry Laboratory glassware Experiment
TITLE: BASIC LABORATORY TECHNIQUES (EXPERIMENT 1) NAME: MURSYIDA BINTI MOHD DAKROH(ID: 2015883226) LAB PARTNERS:NABILA SOFEABINTI ZAWAWI (ID: 2015850932) :NUR ANISLYANA BINTI TAMAM (ID: 2015832718) :NUR AUNI BINTI MOHD RADZIFF (ID: 2015863252) LECTURER NAME: MADAM DYIA SYALEYANA BINTI MD.SHUKRI PROGRAM: RAS1201B DATE OF EXPERIMENT: 30 JUNE 2015 OBJECTIVE 1. To learn the qualitative and quantitative aspect of common laboratory equipment
Free Laboratory glassware Titration Erlenmeyer flask