LAB OF ENTHALPY CHANGE IN COMBUSTION Objective: Determine the Enthalpy change of combustion ΔHc of three different alcohols. Methanol‚ Ethanol and Isopropilic acid. Procedure: 1. Fill the spirit micro burner with Ethanol and weight it 2. Pour 100 cm3 of water into the aluminum cup 3. Arrange the cup a short distance over the micro burner 4. Measure the temperature of water 5. When the temperature of the water has risen by 10°C‚ record the temperature. 6. Reweight
Premium Oxygen Ethanol Carbon dioxide
Displacement On A Downward Ramp 3/3/2014 Purpose: To determine the velocity and acceleration of an object at different positions going down a ramp at four different angles. Hypothesis: If an object is accelerating at different angles then the larger angles will always have the largest acceleration. Materials: Ramp Miniature car Ticker Machine Masking tape Ticker tape Carbon paper Power supply Ruler Procedure: 1. A ramp was angled at 3 degrees and a ticker machine
Premium Velocity UCI race classifications Tour de Georgia
Measurements Lab Name Length Measurements – Follow the Instructions in the Lab Manual and fill in your data in the tables provided. Data Table 1 – Length measurements |Object |Length (cm) |Length (mm) |Length (m) | |CD or DVD |12.00 |120.0 |.1200 | |Key
Free Density Water Volume
Be careful with copper (II) sulphate solution it is poisonous and corrosive. handle with care 2. Do NOT BREATH in any gases produced 3. If you touch any of the metals‚ you MUST wash your hands at the end of the lab Procedure: 1. Collect the materials and put on safety equipment. 2. Observe the metals and record your observations. 3. Into separate test tubes‚ place each metal inside. Label accordingly to metal. 4. Measure 5mL of the copper (II) sulphate using the cylinder
Premium Copper Chemical element Chemistry
Lab 4-B Purpose The purpose of this lab is to test these solutions and see what type of reaction occurs and see if a precipitate or gas forms between any of these reactions. Research 1. Table A Reactants in Aqueous Solutions Predictions (1) MgCl₂(aq) + 2NaOH(aq) Mg(OH)₂(s) + 2NaCl(aq) (2) FeCl₃(aq) + 3NaOH(aq) Fe(OH)₃(s) + 3NaCl(aq) (3) 2KCl(aq) + Na₂SO₄(aq) K₂SO₄(s) + 2NaCl(aq) (4) CaCl₂(aq) + 2AgNO₃(aq) Ca(NO₃)₂(s) + Ag₂Cl(aq) (5) CuSO₄(aq) + Na₃PO₄(aq) Cu₃PO₄(aq) + Na₂SO₄(s) 2. Table B
Premium Chemistry Chemical reaction Chlorine
Name Lab‚ Week #1 BALANCE LAB Introduction Several instruments are used for determining the mass of a chemical; these instruments are called “balances.” However‚ different balances have different measurements‚ meaning that some balances are more accurate than others. Moreover‚ there are several techniques that are used or practiced in order to obtain an accurate measurement. The two techniques are direct weighing and weighing by difference. Direct weighing simply means to read the mass
Premium Measurement Mass Weight
The purpose of lab number thirteen was to examine the response of the daphnia to a chemical stimulant. Also examined was how human resting heart rates differed from the daphnia’s. Stimulants are any substances that raise the levels of activity in the body. Stimulants could be a number of things such as physical or chemical. Physical stimulus usually deal with something that affects the five senses such as sight‚ hearing these could be attributed to loud noises or too much light going into your eye
Premium Drug addiction Addiction Heroin
The investigation on the average mass of DNA with the mass of banana‚ strawberry and kiwi. Purpose: The purpose of this lab is to investigate the comparison between the amount of DNA per gram of fruit that can be extracted from a banana‚ strawberry and kiwi and to determine which one has more DNA. Hypothesis: The banana genome contains 837 MBPs and the strawberry genome contains 206 MBPs and the kiwi genome contains 128 MBPs. This states that there are more base pairs in a banana genome
Premium Fruit DNA
MATERIAL AND METHODS Stability of cell membrane using pH For the lab experiment for testing the stability of beet cell membranes using pH‚ many materials were used as follows. Obtaining a beet we punch out cores‚ using a cork borer. After washing the cores we put each one inside a separate test tube‚ and added a different pH solution in each one. After 3 minutes in these exposure solutions‚ we took the beet out with a dissecting needle. Then transferred each beet to a separate test tube containing
Premium Cell membrane Water Solvent
By: K 3-28-13 On 3-28-13 in Anatomy and Physiology I got to take part in dissecting a cow eye. My lab partner was . The purpose of dissecting the cow eye was to learn and familiarize the class with the structure of the eye and to locate structures. Materials used were the cow eye‚ scalpel‚ probe‚ tweezers‚ scissors‚ dissection tray‚ gloves‚ paperwork / book‚ paper towel‚ ourselves‚ and our lab partner. My data includes the checklist‚ lab sheets‚ drawing‚ picture‚ and my lab report
Free Eye